亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Morocco

Release time:2023-11-15 10:42:23 Hits: Current position: Home > News

This article mainly introduces:

Morocco hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Morocco synchronous hydraulic cylinder

(Morocco synchronous hydraulic cylinder,produced by Hebei Hengyu company)

synchronous hydraulic cylinder are widely used in Morocco,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed synchronous hydraulic cylinder for customers from Morocco.

Introduction to synchronous hydraulic cylinder:

synchronous hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

The cavitation of the synchronous hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the synchronous hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Regular maintenance of the synchronous hydraulic cylinder includes: regular tightening, synchronous hydraulic cylinder fastening screws and gland screws, synchronous hydraulic cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the synchronous hydraulic cylinder once a year. Clean regularly, the synchronous hydraulic cylinder is cleaned every other year, and the seals are replaced while cleaning.

The pressure of the sliding surface of the synchronous hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the synchronous hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Answers to some questions about synchronous hydraulic cylinder:

What is the valve on the hydraulic cylinder?
Oil valve, relief valve, overload valve, explosion-proof valve, etc., these are very convenient to insert! The oil valve, the overload valve and the blasting valve are very important for larger cylinders. Manufacturers will not offer you the selection. You need to choose the values by yourself according to your system, pump, cylinder, environment, working conditions and other comprehensive consideration!

How many tons can a 10mpa cylinder with a diameter of 100 hold up?
About 8 tons. Algorithm: Cylinder cross-sectional area = π* (100/2) ^2=3.14*2500=7850 square mm = 0.00785 square meters pressure = pressure * Cross-sectional area = 10000000Pa*0.00785 square meters = 78500 n mass = pressure /g = 78500 N ÷9.8 n/kg = 8010 kg = 8.01 Tons.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
2025国产精品自拍视频| 国产在线观看免费AV| 在线精品国品| 色婷婷免费观看视频在线| 亚洲1区少妇乱| 日本人妻免费五月天 - 百度| 几把插小逼| 五十路熟女逼| 超碰免费在线资源| 国产肥熟妇一区二区三区四区五区 | 大黑鸡把艹视频| 女同欧美成人视频| 熟妇人妻中文网| 骚1| 色诱少妇大派对视频| 骚逼鸡巴国产网站| 97资料超碰在线观看| 极品人妻aV在线| 日本超碰在线播放| 蜜桃臀插AV香蕉| 一区二区久骚| 国产精品中文字幕强奸乱伦一区二区三区 | 剑川县| 欧美 国产 传媒 一区| 人妻自慰网站| 一区二区三区在线免费观看| 抽插视频一区二区| 中国熟女少妇草草网| 日本在线欧美在线-亚洲日本在线播| 大鸡巴操小逼动漫| 国产精品乱伦| 国产女同百合91刺激| 久久艹女人| 啊插的人家好爽啊视频| 日本黑人人妻| 欧美日韩成人一级生活片在线观看| 美女亲热鸡插鸡欧美网站| 欧美男女操BⅩx| 蜜桃噜噜e| 婷婷五月天福利| 国产,日韩欧美|