亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Sri Lanka

Release time:2023-11-15 10:41:58 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Sri Lanka stacker cylinder

(Sri Lanka stacker cylinder,produced by Hengyu Hydraulic Co., Ltd)

stacker cylinder are widely used in Sri Lanka,because of no need for deceleration device,long service life,smooth movement.So our company has designed stacker cylinder for customers from Sri Lanka.

Introduction to stacker cylinder:

The wear of the hard chromium plating layer of the stacker cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

stacker cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stacker cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When using the stacker cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the stacker cylinder block. If the stacker cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the stacker cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the stacker cylinder, so that the working efficiency of the stacker cylinder is reduced.

The stacker cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

Answers to some questions about stacker cylinder:

There are four cylinders in the front top of the dump truck. When the second cylinder is lifted to half the height, it suddenly falls back more than 30 cm or so, and the cylinder continues to lift.
The problem is the cylinder, the second section of the different strength of the heart. When the oil supply resistance is small, the first out, when the power is not moving, the cylinder needs to be strong, because the second section needs to pop it out after a while when the pressure is large, the oil can not keep up, so it falls back, and the oil continues to keep up.

How is the hydraulic cylinder selected in the mechanical design manual?
First of all, it is necessary to meet your work needs, and the second is to meet the structural space of the cylinder and accessories. Three to consider the other parameters of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
免费不卡欧美自拍视频| 日美女的必| 大几把干女人| 五月超碰婷婷丁香青青| 国产乱伦一二三| 国产三区福利| 抽差不卡视频| 欧美高清大胆视频在线看| 人妻爆肏中出| 超碰在线播放一成二| 操女人逼系列免費視頻| 午夜福利院在线观看| 日韩国产又粗又大| 日韩欧美成人一级电影在线观看| 我想看男人大鸡巴看女人大鸡巴动鸡巴动 | 中文字幕一区二区色综合久久五月| 五十路人妻在线视频| 熟女国产一区二区三区详情| 波多野吉衣一区二区丝袜| 欧美色图看逼| 日韩毛茸茸av| 操欧美大骚浪贱逼逼v| 亚洲第一狠av| 一区二区三区的大肉棒| 美国大逼美女性生活| 操逼日本小骚逼| 欧美大奶操| 操B网AV在线观看| 1区二区三区日韩欧美黄色网址| 爱搞一区二区三区四区| 无码一区二区欧洲高清| 美女大香蕉在线视频| 被大鸡巴插麻豆视频| 操女主播的嫩逼| 一二三四区在线播放| 国产91捆绑| 不卡不卡不卡不卡色| AV男人操逼天堂| 国产性色aⅴ| 中文解说美女操逼视屏| 4399国产卡1卡2精品|