亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

accumulator hydraulic cylinder Sold to New Zealand

Release time:2023-11-15 10:41:51 Hits: Current position: Home > News

This article mainly introduces:

New Zealand hydraulic cylinder,accumulator hydraulic cylinder manufacturer,accumulator hydraulic cylinder

New Zealand accumulator hydraulic cylinder

(New Zealand accumulator hydraulic cylinder,produced by Hebei Hengyu company)

accumulator hydraulic cylinder are widely used in New Zealand,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed accumulator hydraulic cylinder for customers from New Zealand.

Introduction to accumulator hydraulic cylinder:

When the accumulator hydraulic cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

After chrome plating of the piston rod of the accumulator hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The assembly work of the accumulator hydraulic cylinder has a great impact on the quality of the accumulator hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The cavitation of the accumulator hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the accumulator hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Answers to some questions about accumulator hydraulic cylinder:

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

How to set up the one-way cylinder hydraulic system?
Single acting oil cylinder, that is, an oil cylinder with an oil port, can use two three-way valves to control the cylinder action. The three oil ports are respectively connected to P (oil pump), A (oil cylinder), and T (oil tank). If the oil pump is to run continuously, an electromagnetic relief valve can be added. When the cylinder is not moving, the relief valve can unload the oil pump. You can also add a three-way four-way valve, the middle function is unloaded, two outlets: A connected to the fuel tank, B connected to the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
熟女小穴一区二区三区| 国产丝袜综合中文| 大鸡巴插美女免费在线| 偷拍盗拍亚洲色图图片| 久久久久动态白浆| 国内外成人视频在线你懂的| 美女被艹插插插内射| 日本久久久,我的| 久久黄色小说| 麻豆传媒日韩一区二区| 国产一不卡二卡| 美女被操死直喷水| 久久又粗又大久久| 国产疯狂草逼视频| 91精品一区二区三区在线观看| 逼逼掰开AV| 操逼动漫| 收欧美成人在线视频播放| 熟妇一区日本| 欧美一区二区啊啊啊啊| 美女几巴视频在线观看| 69AV激情| 大鸡巴大肉棒日骚逼逼免费视频网址| 超碰福利姬在线观看| 亚洲AV无码秘 一区二区三区3| b骚逼视频免费网| 久久丫精品系列一区| 国产视频大香蕉| 石原莉奈三区四区在线| 日韩欧美国产综合看| 嗯嗯嗯,好深啊视频| 桦甸市| 免费看AV一区二区| 伊人亚洲成人| 国产av区一区二区| 黑人操日本女人屁股| 国产欧美18禁| 性干综合网| 午夜福利在线大香蕉| 污污污色网站| 日韩啪啪天堂网|