亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Nigeria

Release time:2023-11-15 10:41:46 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Nigeria tilting furnace hydraulic cylinder

(Nigeria tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in Nigeria,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tilting furnace hydraulic cylinder for customers from Nigeria.

Introduction to tilting furnace hydraulic cylinder:

In recent years, the processing process of the tilting furnace hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

tilting furnace hydraulic cylinder body inspection: The inner surface of the tilting furnace hydraulic cylinder and the piston seal are the main factors causing the leakage in the tilting furnace hydraulic cylinder, if the tilting furnace hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the tilting furnace hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

tilting furnace hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

tilting furnace hydraulic cylinder hydraulic oil selection: The recommended working oil viscosity of the tilting furnace hydraulic cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

Answers to some questions about tilting furnace hydraulic cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to use a solenoid valve to control the expansion of a cylinder? Doesn't the solenoid valve only control on/off?
Use the solenoid valve P into A-B (generally equipped with oil circuit board) to connect the oil inlet interface at both ends of the cylinder, and the solenoid valve can be realized by power off (refer to the solenoid valve 2B2L, different solenoid valve actions are different).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大屌操逼网页版| 来个AV在线| 国产一区二区三区四区www.| 意甲:罗马1-0国米| 插插视频一区二区| 十八禁午夜精品网站| 一卡二卡三卡免费精品| 骚逼操逼视频网站| 女同黄色片| 美女主播被操在线| 国产大逼美女| 中字精品丝袜熟女人妻| 老司机精品视频三级片二区| 精品韩国自拍视频| 老湿机免费在线观看视频APP| 一区二区三区难受下面好湿想要免费视频 | 大鸡巴插光身大胸美女| 熟妇在线 中文| 大肉棒一进一出网站视频| 99精品鸡巴| 亚洲一区中文字幕欧美| 香蕉人内射| 韩国大香蕉自拍| 操美女的小穴喷水视频| 啪啪俄罗斯逼逼视频 | 操老阿姨老逼的逼| 专操老熟女五十| 又大又长的鸡巴操| 色TV国产| 嗯嗯~好~爽~嗯~在线观看免费| 大香蕉久热抖阴视频| 亚洲经典一区二区高清| 91小仙仙免费看| 一区二区三区中文字幕女同性恋| 国产成人AV一区在线观看| 久久大逼网| 国产刺激高潮爽91| 无码一区二区久久| 老熟女熟妇一区二区| 日韩操逼视频网址| 日韩美女在线操BAV|