亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to America

Release time:2023-11-15 10:41:42 Hits: Current position: Home > News

This article mainly introduces:

America hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

America tilting furnace hydraulic cylinder

(America tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in America,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tilting furnace hydraulic cylinder for customers from America.

Introduction to tilting furnace hydraulic cylinder:

The tilting furnace hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure tilting furnace hydraulic cylinder can use 20 steel pipe, and the high pressure tilting furnace hydraulic cylinder can use 45 steel pipe.

The cavitation of the tilting furnace hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the tilting furnace hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

The assembly work of the tilting furnace hydraulic cylinder has a great impact on the quality of the tilting furnace hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the tilting furnace hydraulic cylinder is in use, ensure that the tilting furnace hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

Answers to some questions about tilting furnace hydraulic cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

What is the HS code of the hydraulic cylinder?
HS code of hydraulic cylinder; 8412210000 8412210000 Linear hydraulic power unit (hydraulic cylinder) 0.12000 0.35000 0.00000 0.17000 0.00000

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本一区二骚逼少妇| 一本道一二三区乱码免费播放| 嗯嗯啊停三级片| 无码字幕在线毛片护士| 彭山县| 美女操逼黄视频| 嗯嗯啊啊视频高h| 亚洲av1区2区3区在线免费观看| 嗯嗯嗯啊啊好痒视频| 日韩成人手机在线| 嫰bbb操bbb| 欧美鸡巴好大逼逼好紧| 操逼视频网啊啊啊啊啊| 岛国AV有码中文| 色悠悠综合久久久解说| 夫妻生活片91网站| 丁香福利| 欧美骚女操逼视频| 91日本老熟女交| 逼操流白浆| 亚洲少妇熟女一区二区三区| 日本美女操操操| 爆操骚逼免费观看| 木下凛凛子JUL931中文字幕| 色五月婷婷视频在线| 中日韩免费爱爱小视频网站| 肏逼内射视频| 美女午夜福利免费视频| 18禁免费观看视频| 香蕉婷婷在线| 中文字幕中出一区二区三区| 大鸡巴插逼爽| 国产精品国产三级AV| 聂荣县| 五十路肉感| 国产精品在线视频一区二区三区| 大鸡巴肏小穴在线一区二区| 东北老淑女性生活对白| 91人妻久久久久久久久久久久久 | 色鬼综合色88| 亚洲AV韩国二区|