亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Malaysia

Release time:2023-11-14 08:41:11 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Malaysia tilting furnace hydraulic cylinder

(Malaysia tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in Malaysia,because of long service life,smooth movement,high work efficiency.So our company has designed tilting furnace hydraulic cylinder for customers from Malaysia.

Introduction to tilting furnace hydraulic cylinder:

When the tilting furnace hydraulic cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

When the tilting furnace hydraulic cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the tilting furnace hydraulic cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

The tilting furnace hydraulic cylinder is not the same as the tilting furnace hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the tilting furnace hydraulic cylinder can not be used as a high-power power component, but the tilting furnace hydraulic cylinder can be used as a relatively large power component, or the tilting furnace hydraulic cylinder system can be used.

The repair method of the tilting furnace hydraulic cylinder: the repair of the tilting furnace hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about tilting furnace hydraulic cylinder:

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

What should we pay attention to when using the cylinder?
When using the cylinder, we should pay attention to the environment and temperature in which it is located as follows: 1. Before working, the hydraulic cylinder must carry out several reciprocating movements under low pressure (greater than the starting pressure), and work normally after removing the gas in the cylinder. 2. Precautions when removing the hydraulic cylinder: ① The pressure in the hydraulic circuit is reduced to zero before disassembly. ② The screw thread at the top of the piston rod should be prevented from damage when disassembling. ③ Due to the different structure and size of the hydraulic cylinder, the order of disassembly is also slightly different. Generally, the fastening bolt of the end cover should be loosened first. Internal card chain card key application special tools.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
AV一区人妻| 女人操逼逼视频| 潢川县| 首页欧美在线| 69热国产视频| 岛国一本在线综合| 好看的操逼视频一区二区三区| 狂干欧美老女骚穴| 美女小穴视频免费在线观看| AV午夜成人在线| 性欧洲老女人乱配| 日韩无码白浆敏感| 日韩超碰影院| 精品欧美一区二区三区老妇人| 国产偷情自拍一区| 韩国大鸡巴操逼视频| 欧美日韩美少妇| 日逼视屏直接看| 国产美女在线官方| 人妻中文字幕九区| 操白虎大美女小嫩逼| 国产精品自拍午夜小视频| av中文字幕在线观看有码| 操美女的小穴喷水视频| 尤物视频91.| 波多野结衣网页| 青青草社区大香蕉| 一个美女舔另一个美女的大奶的视频网站| 91污视频在线| 丝袜网站污污| 精品国产96亚洲一区二区三区图片| 麻豆日逼录像| 岛国高清免费在线观看| 日韩精品久久久久福利悠悠色 | 嗯嗯操我视频一区二区| 越西县| 亚洲老熟女二区三区| 欧美潮喷老司机在线| 溧水县| 日本美女肏逼视频播放| 大胸美逼美女被操|