亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Germany

Release time:2023-11-08 08:11:37 Hits: Current position: Home > News

This article mainly introduces:

Germany hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Germany track steering cylinder

(Germany track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

track steering cylinder are widely used in Germany,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed track steering cylinder for customers from Germany.

Introduction to track steering cylinder:

When the hydraulic oil is not pumped into the track steering cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the track steering cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

The repair method of track steering cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When producing oil track steering cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

When the track steering cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the track steering cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

Answers to some questions about track steering cylinder:

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

How to calculate hydraulic cylinder thrust?
Cylinder diameter = piston diameter =200MM Piston area =π (200/2) square =3140 square mm =31.4 square cm 25MPA=250KG/ square cm Maximum thrust = pressure * Piston area =250 *31.4 =7850KG=78500 Newtons This is the maximum thrust. The formula can be derived from the calculation formula.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日逼视频高朝| 日韩成品av红桃| 美女嫩逼被操得直流水视频| 日韩老少妇| 日韩美女和中国美女靠逼一一一一一| 欧美不卡视频一区发布| 啊啊啊好爽操我啊啊啊视频网站| 大鸡巴插逼逼免费视频观看| oo美女一区二区三区| 新干县| 国产黑色丝袜看片| 一区二区三区在线观看天堂| 天天插天天干| 中文字幕_绯色av| 熟女偷拍精品网| 人人操人人干天天爽| 大香蕉网在线视频韩国日本| 午夜福利激情院| 深爱激情视频在线观看| 性爱视频一二三区| 情爱视频日韩无| 泰国无码视频自拍| 东北大粗鸡巴操熟妇国产视频| WWW黄片,在线看| 鸡巴操小穴网站| 日韩AV 一卡二卡| 美洲精品一区二区| 白白白白操| 自拍偷拍136| 大黑吊插美女AV| 欧洲福利精品视频| 嗯嗯,,,啊艹视频| 插逼视频啊啊啊要| 亚洲色丰满少妇高潮| 大香蕉KB| 20超碰资源| 91少妇激情自慰床| 亚洲日韩操逼逼| 欧美少妇一个人在家一区| 石原莉奈无码在线| 日韩欧美国产精品大陆夫妻|