亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

yg series hydraulic cylinder Sold to Kenya

Release time:2023-11-08 08:11:36 Hits: Current position: Home > News

This article mainly introduces:

Kenya hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

Kenya yg series hydraulic cylinder

(Kenya yg series hydraulic cylinder,produced by Hengyu Group)

yg series hydraulic cylinder are widely used in Kenya,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed yg series hydraulic cylinder for customers from Kenya.

Introduction to yg series hydraulic cylinder:

yg series hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The oil yg series hydraulic cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

If the seal of the yg series hydraulic cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and yg series hydraulic cylinder, and the phenomenon of "pulling the yg series hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

How to determine the working pressure of the yg series hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, yg series hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about yg series hydraulic cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to set the stroke of the cylinder?
Self-design should be based on product demand and practical application. The stroke of standard cylinder depends on the parameters the customer requires. The hydraulic cylinder is a linear motion actuator whose output force is proportional to the effective area of the piston and the pressure difference on both sides. Its function is to convert hydraulic energy into mechanical energy. The input of the hydraulic cylinder is the flow rate and pressure of the fluid, and the output is the speed and force of the linear motion. The piston of the hydraulic cylinder can complete the linear reciprocating movement, and the linear displacement of the output is limited. Hydraulic cylinder is an energy conversion device that converts hydraulic energy into mechanical energy of reciprocating linear motion. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston and piston rod, sealing device, buffer device and exhaust device.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
鸡巴插进精品| 美女操逼做爱视频| 嗯嗯啊啊啊免费看片| 欧美精品自拍视频网站区| 在线日本有码| 最新日韩色片大香蕉在线| 日本人妻黑人系列| 蜜乳高清在线| 老司机精品视频三级片二区| 日韩一区二区三区在线| 台湾佬美性中文娱乐入网| 欧美熟女无吗视频| 亚洲黄AV一区二区在线观看| 小女生被操网站视频| 好怀念的大鸡巴AV| 操逼大杂绘视频| 木下凛凛子国产AV二区| 欧美美女舔白虎| 无码视频一区二区日本熟妇免费| 在线欧美卡通视频| 中文字慕一区二区网站| 黑白丝女生被操出水视频网站| 日韩大香蕉系列| 三级区免费看中文网站| 黄片大寄吧| 东京热一起草加勒比海一区二区| 600部日韩成人视频在线观看| 欧美偷拍兔费视频| 货骚逼成人AV首页| 中文字幕乱码一区av久| 亚洲国产破| 涩涩香蕉网| 中文字幕三级片中出| 全裸美女操b网站| 晶品美女日逼视频免费看| 丁香福利| 大黑鸡巴狠狠操美女| 亚洲女人日B| 大鸡巴日女人在线播放| 午夜成人福利在线观| 婷婷五月亚洲给合网|