亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Republic of Lithuania

Release time:2023-11-13 11:19:55 Hits: Current position: Home > News

This article mainly introduces:

Republic of Lithuania hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Republic of Lithuania shearing machine cylinder

(Republic of Lithuania shearing machine cylinder,produced by Hengyu Hydraulic Co., Ltd)

shearing machine cylinder are widely used in Republic of Lithuania,because of no transmission clearance,excellent temperature resistance,powerful torque.So our company has designed shearing machine cylinder for customers from Republic of Lithuania.

Introduction to shearing machine cylinder:

The shearing machine cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the shearing machine cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the shearing machine cylinder wall due to the stiffness and the weight of the parts, causing scars.

The material of the sliding part of the shearing machine cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

When the shearing machine cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the shearing machine cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil shearing machine cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical shearing machine cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the shearing machine cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The repair method of shearing machine cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about shearing machine cylinder:

Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.

How to control the speed of the hydraulic cylinder?
The speed of the hydraulic cylinder is only related to the flow, so the control speed is to control the flow of the hydraulic oil, which is generally adjusted by the throttle valve in the system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产天仙自拍小视频| 中国操 B| 好大好爽啊还想要视频| www操逼| 亚洲一区二区电影在线观看AV| 一级一级黄片| 欧美熟女在线插| 国产的黄色老女人91| 肏肏小穴二区| 激情文学在线视频欧美| 1美女逼视屏| 欧美美女淫乱视频一区二区三区| 午夜av色阁| 久久久久mf| 勉费看插逼| 日韩情爱视频与淫免费看| 最新加勒比视频| 久久黑丝最新| 五月激情四射AV中文字幕| 亚洲欧av 1区二区| 午夜欧美嗯啊| 日本有码中文字幕h| 日韩女优| 熟女五十路一二三区| 免费看多人操逼视频| 美女逼久久| 三级免费网址| 韩国尤物视频不卡在线观看| 操小美女骚穴视频| 大鸡巴插小穴在线看 | 亚洲国产AV一级| 美女被男人桶爽免费视频| 大香蕉一本在线中文| 国产精华91成人蜜臀| 午夜男女爱| 日韩国人妻视频网| 欧美无遮挡国产视频| 人人人人操美女| 草鸡巴逼逼| 大鸡吧插小穴视频重口| ab中文一区二区三区不卡|