亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Slovakia

Release time:2023-11-13 11:19:49 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Slovakia stern plate hydraulic cylinder

(Slovakia stern plate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stern plate hydraulic cylinder are widely used in Slovakia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed stern plate hydraulic cylinder for customers from Slovakia.

Introduction to stern plate hydraulic cylinder:

The stern plate hydraulic cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

When purchasing the stern plate hydraulic cylinder, try to clarify the following parameters of the stern plate hydraulic cylinder: A. stern plate hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or stern plate hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right stern plate hydraulic cylinder type can be found accurately and quickly.

The stern plate hydraulic cylinder should be vented: when the stern plate hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the stern plate hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the stern plate hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the stern plate hydraulic cylinder, the oil is best entered and discharged from the highest point of the stern plate hydraulic cylinder. stern plate hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When installing the stern plate hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stern plate hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the stern plate hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stern plate hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stern plate hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about stern plate hydraulic cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

What is the role of the cylinder on the plastic mold? The oil cylinder plays a great role in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the oil cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product, sometimes customers require to use hot runner, the price is more expensive, but there are many benefits. It can save raw materials and shorten the molding cycle.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产情侣碰碰碰| 欧美大鸡巴免费视频| 国产帅哥美女大鸡巴艹逼| 大鸡巴插嫩逼的| 国产少妇厕所自慰喷| 欧美色逼女| 亚洲熟女9区| 午夜成人AV剧场| 直接可以看的日美女小逼逼视频| 非洲一汲大黄片免费看| 国产 丝袜 人妻 制服 一区| 超碰大香蕉大香蕉| 操一操日一日| 青青草原午夜影院更狠操| 国产对白麻豆激情对白| 视频在线中国欧美| 肉棒后入视频| 厦门少妇毛片| 操逼漏脸| 久久婷婷字幕| 日本最新操逼网站| 欧美大鸡巴做爱网吧| 日本熟妇性交一区二区三区| 啊啊骚逼要视频| 唐山市| 亚洲AV免费~区二区三区| 91爆操熟女| 亚洲91麻豆视频| 激情不卡| 日本成人一区二区中文字幕| av高清在线观看一区| 亚洲aiai视频| 国产毛片九九九| 久久国产农村夫妻性生活视频| 在线超碰免费香蕉观看| 一二三四五在线观看免费中文视频 | 美女在干逼| 插日本熟女| 国产三级办公室| 色诱在线免费视频| 大鸡吧操小骚逼啊|