亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

land leveller hydraulic cylinder Sold to Uzbekistan

Release time:2023-11-13 11:19:42 Hits: Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,land leveller hydraulic cylinder manufacturer,land leveller hydraulic cylinder

Uzbekistan land leveller hydraulic cylinder

(Uzbekistan land leveller hydraulic cylinder,produced by Hengyu Group)

land leveller hydraulic cylinder are widely used in Uzbekistan,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed land leveller hydraulic cylinder for customers from Uzbekistan.

Introduction to land leveller hydraulic cylinder:

How to determine the working pressure of the land leveller hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, land leveller hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

The scar on the sliding surface of the land leveller hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the land leveller hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

The method of sleeve land leveller hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the land leveller hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the land leveller hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

Because of the slightly complex structure of the buffer land leveller hydraulic cylinder, sometimes there will be problems, such as when the land leveller hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

Answers to some questions about land leveller hydraulic cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to calculate the hydraulic cylinder pressure, how much pressure can put up how much weight?
There is a formula for air pressure, hydraulic pressure, water pressure: F=P×S type: f-cylinder or hydraulic cylinder output, unit is Newton (N) P- pressure, unit is Mpa S- effective area, unit is square millimeter (mm2), note: is the effective area, in the hydraulic cylinder to subtract the cross-sectional area of the piston rod.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩黑人| 插入小穴视频观看| 五月婷婷手机免费免费观看| 大屁股人妻一区二区三区| 色噜噜噜国产| 一级黄色电影中文字幕| 国产又粗又大配频| 中文色中出在线| 欧美日韩在线簧片| 黄色频道3区| 国产精品少妇视频| 天天干视频在线观看者| 女同逼视频免费| 在线免费观看日韩欧美一级片| 蜜臀三级网站| 玩偶姐姐国产无码一区| 国产A址一址二区| 日韩大鸡吧操小逼免费视频| 激情五月四房播播在线观看视频| 丝袜人妻3p网站| 91人妻啪啪资源站| 熟女成人在线| 中文字幕avtt| 美国草逼网站| 亚洲性生活视频在线播放| 一区二区三区av无码| 蜜臀色欲av午夜久久久一区二区影视 | 欧美亚洲国产日韩另类| 日韩精品一级视频一区| 免费日韩性爱视频网站| 夫妻性生活免费视频。| 成人抓奶子的视频在线播放| 九九精品三级| 九一一区二区三区精品视频| 亚洲第一第二第三av在线| 中文在线中文视频| 淫荡一区二区| 肉丝一区AV| 99香蕉国产视频| 五月天av资源| 日本大香蕉一二三|