亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Nepal

Release time:2023-11-13 11:19:40 Hits: Current position: Home > News

This article mainly introduces:

Nepal hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Nepal stern plate hydraulic cylinder

(Nepal stern plate hydraulic cylinder,produced by Hengyu Group)

stern plate hydraulic cylinder are widely used in Nepal,because of long service life,clever hydraulic energy conversion,no transmission clearance.So our company has designed stern plate hydraulic cylinder for customers from Nepal.

Introduction to stern plate hydraulic cylinder:

If the piston rod and stern plate hydraulic cylinder are stuck or the stern plate hydraulic cylinder is blocked, at this time, no matter how to operate, the stern plate hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the stern plate hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Most of the failure of the stern plate hydraulic cylinder is because there is a foreign body in the stern plate hydraulic cylinder into the failure of the stern plate hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the stern plate hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

The stern plate hydraulic cylinder is mainly composed of body, piston, piston rod, stern plate hydraulic cylinder head, stern plate hydraulic cylinder bottom, piston rod head and related auxiliary devices. The piston divides the stern plate hydraulic cylinder into two chambers, and moves reciprocally in the stern plate hydraulic cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the stern plate hydraulic cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the stern plate hydraulic cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the stern plate hydraulic cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the stern plate hydraulic cylinder bottom and the stern plate hydraulic cylinder head is serious, so the buffer deceleration should be set at both ends of the stern plate hydraulic cylinder The working medium of the stern plate hydraulic cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; stern plate hydraulic cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the stern plate hydraulic cylinder: The buffer structure of the stern plate hydraulic cylinder is to prevent the piston from colliding with the stern plate hydraulic cylinder head at the end of the stroke.

Answers to some questions about stern plate hydraulic cylinder:

What is st represented in the cylinder formula?
St is the original unit of kinematic viscosity, the abbreviation of Stokes, that is, Stokes, short for S. cm2/s has now been used. 1 s (St) = 10^-4m2/s.

How to design the guide sleeve of cylinder diameter 400?
The purpose of the guide sleeve is to guide and seal. Therefore, it is necessary to look at the speed of the piston rod, working pressure and radial force. High speed, medium pressure, no (or very little) radial force, with a Steseal. Low speed and heavy load, medium radial force, combined seal. High speed and heavy load, large radial force, sealed with DU sleeve + copper ring + combination. The combination seal must have a lubricating oil passage, and a seal must be added to the outside of the oil passage.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
老司机福利精品视频伊人| 亚洲大屌肏逼| 婷婷久欧美| 欧美大屌鸡巴操爽| www.日韩性爱视频co m| 亚洲一区二区精品老妇| 人人人人操操人人人| 中文字幕不卡视频久久久| 无码肛交日韩| 超碰射妹子国产欧美日韩| 狂虐老熟女高潮| 亚洲好逼网| 日日操夜夜操天天操人人操| 最爽最乳美女在线| 日韩一区二区三区波多结久久精品| 啊啊啊 舒服 用力 操我 干我 视频| 抽插嗯啊水流大av| 美女色情福利在线| 永宁县| 熟妇综合视频在线| 五月天婷婷一区二区| 国产福利美女| 大鸡巴插贱逼的视频| 又湿又紧又爽视频黄| 大鸡巴插女人逼逼视频| 熟女无套一区| 骚逼湿了 视频| 北岛玲成人在线| 美女被抽插视频91| 免费看骚批视频| 熟妇大屁屁一区二区三区| 小穴啊爽16P亚洲精品| 大奶子综合网| 亚洲高清成人视频| 日本少妇中出| 在线观看日韩 国产 欧美| 高清在线不卡 婷婷 五月| 踢嫩逼鸡巴视频网站| 大肉棒一进一出视频來了| 熟女精品av一区二区三区| 嗯嗯啊啊插中文字幕在线观看|