亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering cylinder Sold to Latvia

Release time:2023-11-13 11:19:38 Hits: Current position: Home > News

This article mainly introduces:

Latvia hydraulic cylinder,steering cylinder manufacturer,steering cylinder

Latvia steering cylinder

(Latvia steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

steering cylinder are widely used in Latvia,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed steering cylinder for customers from Latvia.

Introduction to steering cylinder:

Protection of the steering cylinder surface: During the dismantling process, safety protection should be carried out on the steering cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the steering cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the steering cylinder should be cleaned up in time.

When the control pressure of the hydraulic system is too low, the steering cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

When producing oil steering cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

Most of the failure of the steering cylinder is because there is a foreign body in the steering cylinder into the failure of the steering cylinder, the most problematic is that it is difficult to determine when the foreign body is into the steering cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about steering cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

How to determine the rated working pressure of the hydraulic cylinder?
Under normal circumstances, the working pressure is determined according to the size of the load and the installation space (the allowable diameter of the cylinder). In some special occasions, the smaller the cylinder, the better, the pressure level must be increased. The cylinder pressure is related to the estimated cost. The higher the pressure, the thicker the wall, the higher the cost, but conversely, the lower the pressure, the larger the diameter of the cylinder (when the same thrust) is required, the same high cost. Therefore, the rated pressure of the cylinder is concentrated in about 35 mpa, taking into account the cylinder diameter and wall thickness.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
逼逼宝贝| 91精品国产综合久久久蜜臀不卡| 亚洲第一福利精品美女| 麻w痘w视频| 蜜臀一二区三区| 大黑屌好大好爽| 人妻女推油被中岀| 欧美系列在线青青草| 国产一级av线上观看 | 美国成年人噜噜噜| 日本逼逼精品在线| 久久精品美国| 中韩美女一区二区三区在线观看 | 超碰动漫福利| 骚逼社区免费视频免费观看| 妓女自由AV| 精品逼站| 波多野结衣淫乱视频| av网站黄色仓库| 免费看偷拍小视频| 欧美大鸡巴操逼逼谈话精选| 亚洲一二怡| 最大级黑人大鸡巴av| 日本三级韩国三级中文字幕 | 大鸡巴插贱逼的视频| 午夜AV在线播放观看| 精品农村女人AV| 日本操逼大全| 国产精品对白真实在线观看| 我艹91艹逼| 偷拍台湾妹0| 石原莉奈亚洲第一| 日韩精品日逼| 涞源县| 亚洲AV日韩一卡二卡| 欧美操逼能放的| 夂夂综合狠狠| 蜜桃AV极品蜜桃臀上位| 色色插91| 澳大利亚无码三区免费观看| 午夜福利视频乱|