亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Burma

Release time:2023-11-13 11:19:08 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Burma servo hydraulic cylinder

(Burma servo hydraulic cylinder,produced by Hengyu Group)

servo hydraulic cylinder are widely used in Burma,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed servo hydraulic cylinder for customers from Burma.

Introduction to servo hydraulic cylinder:

The piston rod and guide sleeve function of the servo hydraulic cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

In order to ensure the service life of the servo hydraulic cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the servo hydraulic cylinder, causing damage to the seal and causing leakage in the servo hydraulic cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

If the piston rod and servo hydraulic cylinder are stuck or the servo hydraulic cylinder is blocked, at this time, no matter how to operate, the servo hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the servo hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

In the process of using the servo hydraulic cylinder, sometimes such a problem will occur, the servo hydraulic cylinder can not act immediately after the instruction of the servo hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil servo hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about servo hydraulic cylinder:

What are the cylinder manufacturing processes?
Hydraulic cylinder processing process: 1, cylinder: a, material preparation (seamless steel pipe) → inspection (material certificate, etc.) → tempering (outsourcing: Some parts) → car (car round, shelf mouth, boring, flange stop, etc.) → tempered hardness test → welding (welded pipe joint base, flange and other accessories) → boring or honing (rough boring, fine boring, rolling) → car (hole slot or internal and external thread) → fitter (drilling) → inspection → rust prevention storage b, material preparation (forgings) → inspection (material certificate, inspection, etc.) → welding (blank butt welding) → welding inspection → car (rough car) → quality control (outsourcing: some parts) → car (car round, shelf mouth, boring stop, flange stop, etc.)

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
96久久日一区二区三区| 91视频网久久一区二区| 爆操94美女| 美女脱衣服一区二区在线| 国产高清婷婷五月| 在线观看视频在线国产一区二区| 蜜臀色超碰| 亚洲乱码视频综合| 被抽插 无码| 大鸡巴 日逼| 欧美大逼精品操老太太大逼| 香蕉久久久国产黄视频| 日韩地址一二三四区| 91超碰大香蕉C| 禁网站美女| 性欧美日本精品一区二区三区在线播放| 午夜福利午夜福利av| 131美女久久短视频| 欧美大鸡巴日大BAV在线| 日本操逼精品在线播放| 考逼鸡巴艹逼视频网站| 青青操逼比里面视频| 操四川BB娇小BB痒BB| 亚洲精品色图| 骚逼一区二区网| 精品www日韩熟女人妻| 亚洲无码淫水黑鬼| 大鸡巴操我~| 超碰97公开在线观看| 日本女人日B照片| 激情丝袜少妇伊人国产| 欧美在线免费资源头91青青草 | 日日躁狠狠躁| Av不卡女色在线| 天天干夜干夜| 女生18禁无遮挡| 黑人巨屌XXXX| 国产操逼视频不卡| 美女张开脚给男人桶麻豆| 日逼视频啊啊啊| 骚逼十分钟视频|