亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

unidirectional cylinder Sold to Argentina

Release time:2023-11-07 17:48:08 Hits: Current position: Home > News

This article mainly introduces:

Argentina hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

Argentina unidirectional cylinder

(Argentina unidirectional cylinder,produced by Hengyu Hydraulic Cylinder Factory)

unidirectional cylinder are widely used in Argentina,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed unidirectional cylinder for customers from Argentina.

Introduction to unidirectional cylinder:

The repair method of the unidirectional cylinder: the repair of the unidirectional cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The body of the unidirectional cylinder on the processing process requirements: the body of the unidirectional cylinder is an important and essential part of the unidirectional cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the unidirectional cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

The unidirectional cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

What kind of process is used in the unidirectional cylinder to make high-quality unidirectional cylinder products: the body is the main component of the unidirectional cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The unidirectional cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the unidirectional cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the unidirectional cylinder increases by 25%. If the service life of the unidirectional cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. unidirectional cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the unidirectional cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and unidirectional cylinder are stuck or the unidirectional cylinder is blocked. At this time, no matter how to manipulate, the unidirectional cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the unidirectional cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about unidirectional cylinder:

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

How to select the 2.5T bearing cylinder and hydraulic pump?
2,5 ton load is not heavy, you can use the rated pressure of 16 mpa gear pump, neither waste nor save cost, load/pressure = cylinder diameter, preset pressure of 8 mpa, 2500 (kg) /80 (bar) =31.25 square centimeters, in the open =63 mm, cylinder diameter can be selected 63 mm, stroke according to the situation, Hydraulic pump select gear pump, if there is a speed requirement, in order to calculate the displacement, the motor power also needs to determine the displacement of the pump to calculate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
激情短视频久久| 天天看天天搞| 91黄色免费电影| 在线日本中文字幕视频| 几把插入北操视频| 免费看操美女的真逼视频| 日本户外一区二区网站| 老湿官网| 日本有码二区在线| 伊人五月天综合在线| 日本熟妇的肉感| 老熟女一区二区黄色录像| 亚洲欧洲综合分析在线| 色五月婷婷亚洲一区| 亚州少妇女亚州精品| 日韩中出片| 日本人妻在线中字| 毛片一区二区三区四区五区六区| 日韩性爱视频网站免费观看| 哥也搞在线日韩欧美| 老湿机视频在线| 青青草原成人电影| 涩婷婷五月在线观看| 操逼97大鸡吧| 台湾娱乐中文妹子网| 骚女激情AV| 欧美胡逼鸡巴大操| 公交车被cao到腿软H漫画视频| 激情综合网五月激情综合俺也去| 操逼白虎喷水| 老司机黄网一区| 精品自拍小视频色| 鸡巴骚逼视频| 日本成人精品久久久| 91Av人妻| 欧美日韩啪啪啪片| 后入av成人电影| 女的扒开尿口让男人插30分钟久久久| 台湾佬中文娱乐网2xxoo| 日本综合不卡视频在线/| 青青少妇|