亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push plate cylinder Sold to Britain

Release time:2023-11-12 15:33:27 Hits: Current position: Home > News

This article mainly introduces:

Britain hydraulic cylinder,push plate cylinder manufacturer,push plate cylinder

Britain push plate cylinder

(Britain push plate cylinder,produced by Hebei Hengyu company)

push plate cylinder are widely used in Britain,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed push plate cylinder for customers from Britain.

Introduction to push plate cylinder:

push plate cylinder piston rod material introduction: In general, we use 45 steel to produce push plate cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

At the rated pressure, the thrust of the push plate cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the push plate cylinder is related to the diameter of the push plate cylinder, but not to the stroke of the push plate cylinder. Moreover, the larger the push plate cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the push plate cylinder.

Under normal circumstances, the push plate cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the push plate cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the push plate cylinder and the end cover, the piston and the piston rod, the piston and the push plate cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the push plate cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

The quality of the push plate cylinder can not be ignored in the purchase of the push plate cylinder. The push plate cylinder is the main component of the push plate cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. push plate cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of push plate cylinder is deep hole processing, which has always troubled the processing personnel.

Answers to some questions about push plate cylinder:

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
草小骚逼福利视频| 日韩视频 有码| 狼操狠操美女的逼逼| 石原莉奈在线不卡日本| 情欲AV一区二区| 黑人和亚洲人无码操逼视频| 大香蕉 视频一区| 成人自拍内射| 亚洲综合性爱视屏| 欧美美女爱大屌| 无码一区二区三区96| 人妻 丝袜 中文字幕| 中出性视频,| 操逼视频尻我逼骚| av一二三四区在线观看| 一区二区三区四区五区六区视频| 中国三级片天天操| 五十路六十路老熟妇挑情视频播放| 老司机在线精品视频lsj桃| 淫荡老熟女一区| 亚洲大片一区二区三区跳转| caoporn潮喷在线| 欧美一区二区三区展阴视频| 免费靠逼视频欧美二区| 亚洲美日韩AV一区二区三区| 大黑鸡巴插逼视频免费| 美美女插逼视频A| 欧美呦呦裸体视频| 免费黄片靠逼| 喷白浆熟女精品一区二区三区 | 亚洲一级qv| 美女被操大鸡巴| 素人精品区| 天天天玩夜夜夜爽| 爱福利一区二区| 射五月av| 日本操逼大全| 欧洲无码区| 青青操2024| 久久123成人不卡| 精品自拍在线观看|