亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push and pull the cylinder Sold to Tanzania

Release time:2023-11-12 15:33:16 Hits: Current position: Home > News

This article mainly introduces:

Tanzania hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

Tanzania push and pull the cylinder

(Tanzania push and pull the cylinder,produced by Hengyu Group)

push and pull the cylinder are widely used in Tanzania,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed push and pull the cylinder for customers from Tanzania.

Introduction to push and pull the cylinder:

When the long-stroke push and pull the cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in push and pull the cylinder head seal damage, oil leakage, and piston sleep in the push and pull the cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the push and pull the cylinder; The piston and the piston rod are connected with a spherical joint.

When installing the push and pull the cylinder, the axial ends of the push and pull the cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the push and pull the cylinder, there is axial expansion. If the two ends of the push and pull the cylinder are fixed, all parts of the push and pull the cylinder will be deformed. When disassembling the push and pull the cylinder, it is strictly forbidden to hammer the push and pull the cylinder and the piston surface, such as the push and pull the cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

push and pull the cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

When the oil pressure of the push and pull the cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about push and pull the cylinder:

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

What is a two-way hydraulic cylinder?
Bidirectional hydraulic cylinder definition: The bidirectional hydraulic cylinder uses the oil as the working medium, transmits the movement through the change of the sealing volume, and transmits the power through the pressure inside the oil. The two-way cylinder has at least two oil ports, which are used to connect the hydraulic tubing, and control the extension and retraction of the cylinder by pressing.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
伊人大香蕉观察| 美女女优一区二区| 日本熟妇五十路在线视频| 国产av街头| 国产精品九一在线| 草插日亚洲七色七色操插日| 美女网站n| 都市淫乱大香蕉| 少妇自慰91| 欧美日韩黄片一级| av免费在线观看大鸡巴| 国产欧美日韩三级黄片| 大香蕉日骚| 美国大屁股日逼| 嗯啊啊啊啊大鸡巴视频| 无遮挡羞辱美女网站| 破除在线观看| 五月天精品婷婷国产剧情网站系列| 操逼美女免费视频| 91啪啪啪啪啪啪啪视频| 亚洲奇米精品一区二区三区| 国产三级人妻| 中国美女干大逼| 亚洲福利视频看逼| 亚洲夜午| 中文超碰在线| 婷婷五月基地传媒| 温柔的抽插视频| 午夜av在线网| 免费av一区国产| 后入大屁股国产在线| txxx91熟女| 国内自拍视频 麻豆| 国产美日韩在线播放| 欧美日韩成人电影在线| av男人的午夜做爱天堂| 一区二区三区成人午夜| 亚洲人成五月天婷婷| av熟女人妻自拍偷拍| 九九热只有精品6| 成人熟女人区一三区|