亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Latvia

Release time:2023-11-07 17:48:06 Hits: Current position: Home > News

This article mainly introduces:

Latvia hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Latvia supporting cylinder

(Latvia supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

supporting cylinder are widely used in Latvia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed supporting cylinder for customers from Latvia.

Introduction to supporting cylinder:

If the seal of the supporting cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

If the supporting cylinder slips or crawls, please check whether there is astringency inside the supporting cylinder, because the internal parts of the supporting cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the supporting cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the supporting cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

When the control pressure of the hydraulic system is too low, the supporting cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Do not enter foreign bodies when installing the supporting cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

Answers to some questions about supporting cylinder:

How to calculate multistage cylinder volume?
When the multi-stage cylinder is extended, the largest cylinder is extended first, and when the largest cylinder stroke is completed, the second largest cylinder is extended again, the second largest cylinder stroke is completed, the third largest cylinder is extended again... Therefore, the cylinder extension length is less than the stroke of the largest cylinder, and the volume is the extension length times the inner hole area of the largest cylinder. The cylinder extension length is greater than the maximum cylinder stroke and less than (the largest cylinder stroke + the second largest cylinder stroke), and the volume is the largest cylinder stroke times the internal hole area of the largest cylinder + (the extension length - the largest cylinder stroke) times the second largest cylinder.

A hydraulic system functions three cylinders to maintain pressure, what components need to be used?
Two way cartridge valve can be selected for control. Two way cartridge valve advantages: 1) flow capacity is large, especially suitable for large flow occasions. 2) The spool has sensitive action and strong anti-clogging ability. 3) Good sealing, small leakage, oil flow through the valve pressure loss is small. 4) Simple structure, easy to standardize.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕精品一区二区三区在线视频| 鲍鱼污污在线观看| 女孩把腿张开让男人桶视频| 免费在线看逼| 五十路在线播放免费| 日本女优在线播放一区| 人妻 丝袜 中文字幕| 大鸡巴日女人视频网站| 欧美处大吊操逼| 胖女人莫片三区| 粉嫩欧美一区二区三区| 嗯啊操干视| 美女扒开逼口让男人桶白浆| 美女精品福利在线| 天天操天天扒美女| 黑人大屌日逼视频| 亚洲熟女精品一:区二区三区| 久久四房五月天久久| 国产一区嗯嗯啊啊| 超碰自拍在线| 无码人妻aⅴ一区二区三区麻豆| 大香蕉自拍第一页| 高潮艹逼啊~啊啊视频| 一本伊人久久久| 操鸡视频在线看| 蜜臀AⅤ人妻一区二区三区| 美女午夜欧美| 成人午夜激情福利在线| 青青草原男人资源站在线观看| 大美女大香蕉在线| 韩国深夜三级成人片| 翘臀美女诱惑午夜福利院| 欧洲熟妇×××喷水| 亚洲中文字幕AV| 亚洲一二三区丝袜av| 欧美中文字幕一区二区三区超碰| 色 综合 香| 免费日本熟妇视频| 日本大鸡把网站| 亚洲精品视频专区| 女舔屁眼日本网站|