亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Saudi Arabia

Release time:2023-11-07 17:48:04 Hits: Current position: Home > News

This article mainly introduces:

Saudi Arabia hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Saudi Arabia stern plate hydraulic cylinder

(Saudi Arabia stern plate hydraulic cylinder,produced by Hengyu Group)

stern plate hydraulic cylinder are widely used in Saudi Arabia,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed stern plate hydraulic cylinder for customers from Saudi Arabia.

Introduction to stern plate hydraulic cylinder:

stern plate hydraulic cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a stern plate hydraulic cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' stern plate hydraulic cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the stern plate hydraulic cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The stern plate hydraulic cylinder mainly outputs linear motion and force. The stern plate hydraulic cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston stern plate hydraulic cylinder, plunger stern plate hydraulic cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger stern plate hydraulic cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

The stern plate hydraulic cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the stern plate hydraulic cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the stern plate hydraulic cylinder wall due to the stiffness and the weight of the parts, causing scars.

The machining accuracy of the stern plate hydraulic cylinder depends on the level of equipment, production technology and testing means. stern plate hydraulic cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular stern plate hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about stern plate hydraulic cylinder:

How big is the 100t cylinder pump and how big is the motor?
Load is calculated at 15 tons, stroke is calculated at 100 (both take the maximum) 15 tons = 15,000 kg, 15,000/210 bar (21 mpa) =71.42 square centimeters (cylinder area) 71.42/3,14 In the root *2=90,5 the inner diameter of the cylinder can be taken 100 mm. Travel 100 cm, that is, one meter, assuming 10, seconds a back and forth, then it is six times a minute, six meters per minute, then the required flow is,71,42*600 cm (6 meters) =42840 mm =42.84 liters/minute 42.84*21/60=14.9 kilowatts can choose 1450 RPM 4-stage motor 15KW.

What brand of hydraulic cylinder seal ring is best?
Depending on the specific product, the world famous seal brands are NOK, CFW, PARKER, TSS, WKF, DINGZING DZ, ASTON, HALLITE, TECNOLAN and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲中出大全| 久久a影院禁啊啊啊| 视频嗯嗯啊啊啊在线观看| 日本互操| 内谢美女b| 中文日本在线| 日韩成人性爱视频网站无打码| 中国黄色一级毛片| A V男人的天堂网站| 色悠悠亚洲国产一区| 美女的逼逼被操视频| 五月婷视频在线观看| 亚洲巨逼| 中字中出在线| 人妻插逼| 91导航中文字幕| 美女精网| 淫领全球avav| 亚洲无码视频c胸| 天天干夜夜爽夜夜爽夜夜爽| 老司机不卡视频一区二区| 木下凛凛子人妻| 91yqeqsqzx| 亚洲欧美日韩插JB操逼视频下载网站 | 欧美老妇乱搞一区二区。| 日韩精品在线观看成人一区| 天天日日综合| 欧美大秀美女视频在线观看网址| 大鸡巴干穴在线观看| 被大黑屌狠狠后入| 日韩 麻豆 一区| 中文字幕中日韩欧美毛片| 日本丝袜人妻在线一区二区| 不卡无码日韩一区字幕| 欧美带钩鸡吧操逼网| 久久久一区二区三区麻妃| 抽插骚穴直播| 大香蕉免费在线视频观看| 香蕉视频老湿机在线观看影院APP| 国产熟女露白浆精品视频| 中文人妻熟妇精品乱|