亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Thailand

Release time:2023-11-12 15:32:22 Hits: Current position: Home > News

This article mainly introduces:

Thailand hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Thailand stacker cylinder

(Thailand stacker cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stacker cylinder are widely used in Thailand,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed stacker cylinder for customers from Thailand.

Introduction to stacker cylinder:

The repair method of stacker cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

The difference between the plunger stacker cylinder and the piston stacker cylinder is that the piston in the stacker cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type stacker cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

When the stacker cylinder is installed, the piston and the stacker cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the stacker cylinder head boss is easy to cause scars when it hits the inner surface of the stacker cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized stacker cylinders, only careful and careful operation can be avoided.

stacker cylinders in series, parallel and series parallel. Series: In the stacker cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the stacker cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the stacker cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the stacker cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about stacker cylinder:

Why can't the hydraulic cylinder be pulled back after pushing to the limit?
May be long-term use to the limit position, resulting in serious wear caused! The solution is to add the stroke switch or disassemble and add gaskets before and after the piston.

Why does the hydraulic cylinder not return?
For a spring return cylinder, it is possible that 1, the spring is damaged. You can check it for processing. 2, the oil in the oil path is not unloaded, causing it to be unable to reset. 3, the cylinder piston is dead, resulting in no position. For double-acting cylinders, it is possible to: 1, the spool is not reversed, or is not changed to the correct position, check whether the reversing valve is normal (and whether there is electricity). 2, the cylinder piston is dead, resulting in no position, check and treatment can be. 3, the return oil pressure is insufficient, the inlet oil is not unloaded, the operation is not smooth. For reference only.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
央日韩欧美一二三亚黄色网| 一区二区三区五区六区中文字幕| 啊嗯快嗯嗯在线观看| 3d啪啪视频| 欧美商家在线视频| 又粗又长又硬的大鸡巴艹屄视频 | 欧美大秀美女视频在线观看网址| 美女奶头一区二区| www91一区二区三区| 日本一本久道| 按摩轻轻挺进人妻| 国产女主播操bb| 啪啪人妻视频| 久久一区二区三区精品无码| 水管av超碰在线| 国产老女人性| 舔骚bb视频插入大鸡巴视频| 大美女舔鸡巴网站| 日木大鸡巴在线观看| 操年轻日本女人的逼| 吃瓜国产日韩一区二区| 五十路精品国产| 欧洲毛片。| 国产精品xxx啪啪啪| 国产精品对白视频| 老司机在线精品视频lsj桃| 北京操逼视频| 亚洲中文婷婷| 欧美精美视频在线| 国产网黄色情淫语刺激视频在线观看| 桃色五月天日韩精品国产无码| 美国日逼视频鸡巴装弹珠| 黑人粗大一区二区| 囯产自拍亚洲精品| 美女大鸡吧在现观看| 欧美一级一级日韩| 午夜亚洲一区二区观看| 在线日本有码视频| 主播被操视频| 日美女日BB| 5060人妻交换超碰大鸡巴|