亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

jacking hydraulic cylinder Sold to Azerbaijan

Release time:2023-11-12 15:32:21 Hits: Current position: Home > News

This article mainly introduces:

Azerbaijan hydraulic cylinder,jacking hydraulic cylinder manufacturer,jacking hydraulic cylinder

Azerbaijan jacking hydraulic cylinder

(Azerbaijan jacking hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

jacking hydraulic cylinder are widely used in Azerbaijan,because of long service life,smooth movement,high work efficiency.So our company has designed jacking hydraulic cylinder for customers from Azerbaijan.

Introduction to jacking hydraulic cylinder:

When the jacking hydraulic cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the jacking hydraulic cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

jacking hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching jacking hydraulic cylinder block - fine boring jacking hydraulic cylinder block - grinding jacking hydraulic cylinder block. The rolling method is: broaching jacking hydraulic cylinder block - fine boring jacking hydraulic cylinder block - rolling jacking hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the jacking hydraulic cylinder block is about 1-2 days, rolling 1 meter of the jacking hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the jacking hydraulic cylinder increases by 25%. If the jacking hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality jacking hydraulic cylinders, you must take the rolling production process. After the jacking hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular jacking hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

The jacking hydraulic cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

Answers to some questions about jacking hydraulic cylinder:

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

What is the rated pressure of the general cylinder?
This depends on the model of the cylinder, 1. The rated pressure of the light tie rod cylinder is 7 series 7MPa and 14 series 14MPa. 2. Rated pressure of engineering cylinder 16MPa. 3. Rexroth type metallurgical cylinder rated pressure 250MPa.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
五月激情六月亚洲| 嗯啊嗯啊嗯啊妇女| 精品18视频免费观看| 亚欧一区在线观看| 蜜乳AV一区二区三区四区| 七月婷婷玖玖| 99久久九九视频| a操逼视频| 在线播放中文字幕一区二区三区| 人人干人人操人人射| 猛男av无码在线| 岛国一区二区三区麻豆| 亚州一二三四区| 夜夜操美女av| 欧美大鸡巴日逼好爽啊 | 专干老熟女骚逼| 日本熟妇丰满厨房55| 超碰羞羞99| 婷婷五月成人无码| 91蜜臀网在线观看| 日本日逼视频网站免费| 国产中文制服诱惑| 国产1级Av片在线免费观看| 开心五月国精有线| 嫩穴一区| 青海省| 成人不卡一区在线| 色哟哟国产精| 得得在线播放器| 农村妇女黄色录像| www.色香蕉.| www.cs-cz.com| 美国老太太操逼视频免费看| 国产美女吊鸡巴免费看| 大鸡巴插小B| 日韩精品小黄片在线播放| 中文字幕有码AV在线| 成人精品一区字幕| 操熟女馒头逼| 国产操B好爽东京| 06久久天堂人妻熟女视频|