亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

500 tons hydraulic press cylinder Sold to Republic of Lithuania

Release time:2023-11-12 15:31:26 Hits: Current position: Home > News

This article mainly introduces:

Republic of Lithuania hydraulic cylinder,500 tons hydraulic press cylinder manufacturer,500 tons hydraulic press cylinder

Republic of Lithuania 500 tons hydraulic press cylinder

(Republic of Lithuania 500 tons hydraulic press cylinder,produced by Hebei Hengyu company)

500 tons hydraulic press cylinder are widely used in Republic of Lithuania,because of excellent fatigue and impact resistance,smooth movement,high work efficiency.So our company has designed 500 tons hydraulic press cylinder for customers from Republic of Lithuania.

Introduction to 500 tons hydraulic press cylinder:

The 500 tons hydraulic press cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the 500 tons hydraulic press cylinder, bite. Elimination method: When installing the 500 tons hydraulic press cylinder, ensure that the axis position of the 500 tons hydraulic press cylinder is consistent with the direction of movement; Make the load borne by the 500 tons hydraulic press cylinder as far as possible through the 500 tons hydraulic press cylinder axis, to avoid the phenomenon of eccentricity.

There are some honeycomb holes in the inner wall of the 500 tons hydraulic press cylinder, piston or piston rod surface. How is this formed? When we repair the 500 tons hydraulic press cylinder, we can see that there are some honeycomb holes on the inner wall of the 500 tons hydraulic press cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the 500 tons hydraulic press cylinder is targeted to prevent. Is very necessary.

When the 500 tons hydraulic press cylinder needs to be stored for a period of time, please follow the recommended methods: The 500 tons hydraulic press cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the 500 tons hydraulic press cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil 500 tons hydraulic press cylinder should not be in direct contact with water vapor for a long time. The 500 tons hydraulic press cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the 500 tons hydraulic press cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the 500 tons hydraulic press cylinder Before working, the 500 tons hydraulic press cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the 500 tons hydraulic press cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The definition of the minimum stable speed refers to the minimum movement speed of the 500 tons hydraulic press cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the 500 tons hydraulic press cylinder that undertakes different work has different requirements for the minimum stable speed.

Answers to some questions about 500 tons hydraulic press cylinder:

What are the connection methods of the hydraulic cylinder? The connection modes of the cylinder and the actuator are earring connection, hinge shaft connection, thread connection, etc. The connection modes of tubing and cylinder are threaded connection, flange connection, etc.

How big gear pump need to use for 60*100 cylinder?
One cylinder size alone does not determine the size of the pump used. Choose the size of the pump, at least to know 1, the size of the load is how much, by the size of the load and the size of the cylinder and other conditions can be calculated the pressure required by the hydraulic system. 2. Speed of operation. From this speed and cylinder size, the required flow rate of the system is calculated. The relevant parameters of the pump can be selected by the pressure and flow rate to determine what kind of pump is required.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
极品人妻美妇| 综合在线不卡天天| 操B性爱AV| 国产传媒在线观看欧美日韩| 激情五月男人天堂综合网| 美女18禁免费网战| 欧美黑人操b图| 国产无码操屄视频9| 啊啊啊好痒在线免费观看视频| 日韩国老司机在线播放| 久久五月天亚洲一区二区三区| 蜜臀aⅴ一区二区三区| av亚洲激情| 一本三道a无限码一区v| 爆操美女逼流水视频| 中国黄色特级片无能区| 欧美日韩亚洲性爱| 大鸡巴操小骚逼观看 | 啊嗯,嗯好深好多水家庭视频| 熟女老熟妇爆乳在线视频| 亚洲中文字幕一区精品自拍| 青青草原成人18 在线看| 成人网站 中文字幕| 美女用假鸡吧插逼视频免费| 草b视| 老女人淫乱视频网| 日本艳片一区二区| 99福利一区二区视频| 鸡巴肏屄视频在线免费看| 在线观看被操进去好爽啊啊啊视频| 操鸡视频在线播放| 亚洲狠狠网| 一区二区三区亚洲综合av| 91制黄片| 鸡巴插骚逼,流水视频| xxx日本大鸡巴黑人| 大几八和逼逼美女| 波多野依无码中出| 轻轻操日韩| 熟女内射啪啪| 国产日韩传媒视频在线|