亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Italy

Release time:2023-11-12 15:30:55 Hits: Current position: Home > News

This article mainly introduces:

Italy hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Italy self-locking hydraulic cylinder

(Italy self-locking hydraulic cylinder,produced by Hebei Hengyu company)

self-locking hydraulic cylinder are widely used in Italy,because of no transmission clearance,long service life,smooth movement.So our company has designed self-locking hydraulic cylinder for customers from Italy.

Introduction to self-locking hydraulic cylinder:

When the hydraulic oil is not pumped into the self-locking hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the self-locking hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

If air enters the hydraulic system, the self-locking hydraulic cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

The quality of the self-locking hydraulic cylinder can not be ignored in the purchase of the self-locking hydraulic cylinder. The self-locking hydraulic cylinder is the main component of the self-locking hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. self-locking hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of self-locking hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular self-locking hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about self-locking hydraulic cylinder:

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

There are four cylinders in the front top of the dump truck. When the second cylinder is lifted to half the height, it suddenly falls back more than 30 cm or so, and the cylinder continues to lift.
The problem is the cylinder, the second section of the different strength of the heart. When the oil supply resistance is small, the first out, when the power is not moving, the cylinder needs to be strong, because the second section needs to pop it out after a while when the pressure is large, the oil can not keep up, so it falls back, and the oil continues to keep up.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
淫荡美女丝袜暴操后入| 美女的逼视频播放| 99热色情| 日韩在线观看久久久久久久| 无毛逼逼| 大鸡巴操逼黄色电影免费| 肥熟女精品视频| 老熟女精品导航| 操美女视频网| 中文字幕伦理在线一区二区三区| 吸奶操国产网站| 辰溪县| 和国产精品大鸡巴进进出出| 四虎精品在线播放| 爱爱网址免费一区| 国产六九无码| 操美女的小穴| 少妇诱惑一区| 爱在五月天激情网| 美日韩Av免费看| 大香蕉播放视频| 中文一区二区三区高清| 极品尤物被操爆了| 欧韩又粗又硬| 日B在线免费看| 操骚妇大屁股| 粉嫩嫩欧美日韩大鸡巴| 色69式白浆| 操逼动态嗯| 夜夜伊人综合| 干德国老熟女| japanesesex二区| DeepSeek概念| 骚鸡巴用力操我,爸爸用力视屏| 大鸡鸡操大b| 国国产黄色大片| 五十路色| 91粉嫩喷水| 色18p色| 操丰满美女B视频| 色欲av伊人久久大香线蕉影院|