亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

ejector cylinder Sold to Latvia

Release time:2023-11-12 15:30:53 Hits: Current position: Home > News

This article mainly introduces:

Latvia hydraulic cylinder,ejector cylinder manufacturer,ejector cylinder

Latvia ejector cylinder

(Latvia ejector cylinder,produced by Hengyu Hydraulic Cylinder Factory)

ejector cylinder are widely used in Latvia,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed ejector cylinder for customers from Latvia.

Introduction to ejector cylinder:

The pressure of the sliding surface of the ejector cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the ejector cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

The coordination of the sliding parts of the ejector cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

When the ejector cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

The definition of the minimum starting pressure of the ejector cylinder refers to the minimum working pressure of the ejector cylinder in the no-load state, which is a comprehensive index reflecting the manufacturing and assembly accuracy of the ejector cylinder parts and the size of the sealing friction.

Answers to some questions about ejector cylinder:

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

Is there a way to make the cylinder stop pushing when it hits something hard during the process of pushing?
The simplest solution is to press the stop switch, this switch has a mechanical type, touch the object on the action or send a stop signal, through the operation of the motor control cylinder; There is also an induction switch, that is, when the hydraulic cylinder expands to the range of the induction switch can sense the signal, it sends a signal to let the motor act, resulting in the corresponding action of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩老女人做爱| 猛男的大鸡巴爆插| 欧洲二区无码| 中文字幕 人妻 在线 九 色 91| 精品无码枫花恋| 亚洲 日本 欧美 日韩精品| 大香蕉久久午夜福利| 大鸡八操小逼| 内射白精一区二区三区| 一级黄色片国产| 欧美黄片制服| 日韩 精品 福利 三级 欧美| 欧美老熟女一区| 亚洲超碰福利导航日本| 性少妇视频中国老女人| 女人被男人躁得好爽免费高清视频| 天天舔舔夜夜| 特克斯县| 国产嫩穴在线| 一区二区三区污污久久| 美女射B视频| 小骚逼好想被大鸡吧操视频| 大鸡巴插喉咙视频网站| 丝袜诱惑在线观看一二三| 牛牛影视黄片| 青青草免费黄片| 激情文学 成人| 亚洲美日韩AV一区二区三区| 青青草这里只有精品一区| 亚洲欧美校园春色都市夫妻| 大鸡巴操屄亚洲精品| 国产精品乱理伦片电影| 丝袜理论麻豆蜜臀| 最新日韩综合网| 第一福利视频美女| 瑟瑟综合网91| 欧美 日韩 中文 国产| 超碰日韩欧美在线| 网址一区二区三区激情| 日逼免费视频观看| 网站国产天天爽天天操|