亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

moving truck hydraulic cylinder Sold to Uzbekistan

Release time:2023-11-12 15:30:12 Hits: Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,moving truck hydraulic cylinder manufacturer,moving truck hydraulic cylinder

Uzbekistan moving truck hydraulic cylinder

(Uzbekistan moving truck hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

moving truck hydraulic cylinder are widely used in Uzbekistan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed moving truck hydraulic cylinder for customers from Uzbekistan.

Introduction to moving truck hydraulic cylinder:

moving truck hydraulic cylinder can not drive the load troubleshooting: oil pressure is too low. moving truck hydraulic cylinder selection specifications are too small. Leakage in moving truck hydraulic cylinder or associated hydraulic system element.

When the oil pressure of the moving truck hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

The repair method of the moving truck hydraulic cylinder: the repair of the moving truck hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The moving truck hydraulic cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

Answers to some questions about moving truck hydraulic cylinder:

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

How to remove the lifting cylinder from the forklift truck?
The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产亚州av一级一高清一高清一区| 欧美18网站| 狠狠熟女亚洲| 真皮大奶国产| 亚洲系列精品在线| 操亚洲花B| 另类小说欧美一区| 无码精久久一区| 欧美日韩国产一级毛片| 中出一区二区三区高清在线| wwwxxx国产一区二区三区| 啊…哦~操,逼视频| 日韩50熟妇| 亚洲自拍偷拍性爱视频| 嫩逼逼福利| 人人操综合一区| 戳B免费视频| 91大神在在线免费观看| 激情中文字幕一区| 大肉榛一进一出视频| 日韩AV亚洲 分区一二三| 国产探花日韩熟女| 文学激情校园激情av在线| 骚逼白虎美女被操视频网站| 无码视频在线免费观看| 美女全裸被操视频| 欧美都市激情| 91精品无码免费高清一区二区无码| 日本美女性性视频| 日韩夫妻精品| 激情色一区二区| 亚洲不卡精品人妻| 美女成人大片| 人妻制服丝袜中文| 操妻逼逼福利| 丁香六月色五月欧美视频| 啊啊啊好舒服在线观看视频| 黄片骚逼大鸡吧| 女生18在线观看网站| 18美女禁黄色| 午夜福利激情院|