亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

aluminum alloy cylinder Sold to Australia

Release time:2023-11-12 15:29:46 Hits: Current position: Home > News

This article mainly introduces:

Australia hydraulic cylinder,aluminum alloy cylinder manufacturer,aluminum alloy cylinder

Australia aluminum alloy cylinder

(Australia aluminum alloy cylinder,produced by Hengyu Hydraulic Cylinder Factory)

aluminum alloy cylinder are widely used in Australia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed aluminum alloy cylinder for customers from Australia.

Introduction to aluminum alloy cylinder:

When installing the aluminum alloy cylinder pipe, the pipe should be cleaned after installation, and should not pass through the aluminum alloy cylinder block, and the by-pass pipe must be installed in front of the oil port of the aluminum alloy cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the aluminum alloy cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the aluminum alloy cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

When the aluminum alloy cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

Before purchasing the aluminum alloy cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

aluminum alloy cylinder use should try to avoid sealing belt into the aluminum alloy cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the aluminum alloy cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the aluminum alloy cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

Answers to some questions about aluminum alloy cylinder:

How to store hydraulic cylinder?
After cleaning the hydraulic cylinder with diesel or kerosene, apply lubricating oil and wrap it in oil paper, preferably in a wooden box, and store it in a dry and non-corrosive environment. The outer surface and inner surface of the hydraulic cylinder are sprayed with diesel oil, and the inner layer is covered with cloth and the outer coating of anti-rust oil is good. Put it in a dry place, clean it with diesel oil, and then apply a layer of anti-rust inside and outside the butter.

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中日韩成人免费视频| 亚洲AV成人无码精品网站一区二区 | 嗯啊嗯啊好舒服在线观看| 欧美一区日逼网站| 簧片在线免费看尤物| 鸡巴又粗又长又黄成人网站| 激情国产在线一区二区| 亚洲一二三区无码在线观看| 女人插网| 日韩久久久片| 色A色综合| 欧美中文字幕一区二区三区在线观看| 18禁小视频| 男人天堂AV免费观看在线网站| 日韩午夜福利剧场久久| 白水县| 日本 有码 1页| 亚洲少妇 18P| 插B免费视频美女| 免费看片 中文字幕| 临漳县| V天堂中文字幕| 亚洲女成人熟区| 日本一区二区中出| 欧美自拍视频网站极品| 另类中文日韩欧美视频网站| 泰国AV影院| jibacsib| 麻豆果冻精东一区二区| 日本福利视频二区| 亚洲,欧美,日韩一级视频| 一进一出,网站在线观看| 嗯嗯啊啊哦哦用力视频| 台湾佬中文娱乐欧美| 青青草原av天堂| 午夜福利专区一场| 鸡巴操小穴欧美视频| 加勒比欧美日本在线| 超碰在线观看公开| 巨吊AV在綫| 国产一区二区av在线|