亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic punch cylinder Sold to Ireland

Release time:2023-11-12 15:29:29 Hits: Current position: Home > News

This article mainly introduces:

Ireland hydraulic cylinder,hydraulic punch cylinder manufacturer,hydraulic punch cylinder

Ireland hydraulic punch cylinder

(Ireland hydraulic punch cylinder,produced by Hengyu Group)

hydraulic punch cylinder are widely used in Ireland,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed hydraulic punch cylinder for customers from Ireland.

Introduction to hydraulic punch cylinder:

Before purchasing the hydraulic punch cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

If the hydraulic punch cylinder slips or crawls, please check whether there is astringency inside the hydraulic punch cylinder, because the internal parts of the hydraulic punch cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the hydraulic punch cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the hydraulic punch cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

If the piston rod and hydraulic punch cylinder are stuck or the hydraulic punch cylinder is blocked, at this time, no matter how to operate, the hydraulic punch cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the hydraulic punch cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Causes and countermeasures of oil hydraulic punch cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the hydraulic punch cylinder will lead to premature wear of the piston seal, replace the piston seal; If the hydraulic punch cylinder is visibly scarred, the hydraulic punch cylinder must be replaced. It can be pressurized at one end of the hydraulic punch cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most hydraulic punch cylinder piston drift may not come from the hydraulic punch cylinder, the above method to determine the hydraulic punch cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

Answers to some questions about hydraulic punch cylinder:

How to distinguish high pressure cylinder and low pressure cylinder?
There is no special definition of the cylinder, the so-called pressure classification refers to the pump low pressure (code L) container 0.1MPa ≤p < 1.6MPa; Medium pressure (code M) container 1.6MPa ≤p < 10.0MPa; High pressure (code H) vessel 10 MPa≤p < 100 MPa; Ultra-high pressure (code U) container p≥100MPa. (1MPa=9.8Kg)

How to judge the failure of forklift hydraulic cylinder?
The common faults of the hydraulic cylinder of forklift truck are mainly crawling, insufficient thrust, working speed decline or even stop. Generally, crawling occurs at low speed. The main reason is that the air stored in the cylinder is not cleared. In addition, excessive or uneven mechanical friction can also cause crawling. Such as the piston and the piston rod different heart, the piston rod full length or local bending, the cylinder hole straightness is poor, the cylinder is drum shaped or has a large taper, the cylinder thin finish decline or produce hair, the cylinder installation accuracy is out of whack, the piston rod nuts at both ends of the screw too tight to make its concentricity is poor, the oil seal screw too tight friction is too large, will cause crawling.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91视频3区| 肛交辣妹国产| 尤物在线91| 下载大鸡巴干小逼逼| 深爱激情基地| 大力中出后入人妻中出后入| 欧美午夜成人一二三区成年视频| 久久高跟| 黑人大鸡巴暴操日本美女淫逼视频| 激情天堂中文字幕| 札达县| 三级片大鸡吧搞小逼| 艹逼网站黑润润| avtt一区二区三区在线观看| 国产破逼免费视频| 大黑屌操翘臀美女中文字幕| 97激情成人在线| 亚洲一区二区三区靠逼视频| 在线看小穴| 衄操b网站| 日韩女同一区二区三区熟妇调教| 操女生逼逼视频| 欧美一区二区在线观看| 天天干天天射天天爽亚洲欧美特价精品| 鸡吧插入小逼| 日本中文字乱码字幕| 抽插视频中文字幕| 日韩春药资源在线| 亚洲日韩人体艺术福利一区二区三区| AV一一本道色色| 日本啪啪啪啪| 黄色污污污内射一区二区三区内射丝袜| 国产骚屄视频| 亚洲免费在线观看一二三区| 天天干天天爱天天操| av鸡吧网| 日韩欧美中色| 好骚好紧久久久| 丁香五月婷婷六月| 六月丁香p一二| 色就射一区|