亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Libya

Release time:2023-11-12 15:29:17 Hits: Current position: Home > News

This article mainly introduces:

Libya hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Libya tension cylinder

(Libya tension cylinder,produced by Hebei Hengyu company)

tension cylinder are widely used in Libya,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed tension cylinder for customers from Libya.

Introduction to tension cylinder:

Factors that should be considered when selecting the oil seal in the tension cylinder: some specific factors should be taken into account when selecting the oil seal in the tension cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: tension cylinder diameter, piston rod diameter, piston rod and piston groove size, tension cylinder working pressure, tension cylinder movement speed, hydraulic system oil temperature and tension cylinder working environment.

Before the tension cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

tension cylinder can not drive the load troubleshooting: oil pressure is too low. tension cylinder selection specifications are too small. Leakage in tension cylinder or associated hydraulic system element.

The piston rod of the tension cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

Answers to some questions about tension cylinder:

The two cylinders of the bending machine are out of sync?
Check whether the sliding slide is worn, adjust its tightness, so that both sides are consistent, check whether the two cylinder tubing is connected, tighten the flow valve, pressure, let the cylinder air discharge.

What causes hydraulic cylinder oil leakage?
1. Internal leakage (1) The wear ring on the piston is seriously worn, leading to friction between the piston and the cylinder liner, and finally strain the cylinder liner, piston and seal; 2) Seal long-term use failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) The hydraulic oil is dirty, and a large number of impurities enter the cylinder and wear the piston seal to bad; 2. External leakage 1) cylinder inlet and outlet tubing joint cracking; (This I see in the actual work is still more) 2) The piston rod extension end with the piston rod seal damage, mostly due to the piston cylinder is caused by hair, but also caused by aging; 3) The seal between the extended end of the piston rod and the liner is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大鸡巴插入你的小骚逼| 黑鬼精品成人片在线| 轻轻操热| 中文AV在线播放| 91少妇操| 欧美操B视频看看| 日本户外一区二区网站| 鸡巴搞逼片| 麻豆传媒高清一区| 国产综合3| 亚洲美日韩成人片| 五月六月婷婷青青操丝袜| 欧美操大虎逼视频| 婷婷综合在线观看| 大香蕉视频在线播放一区| 国产不卡一区AV| 午夜成人免费一区| 建湖县| 国产黄片×××| 日本好热热视频都是精品| 蜜桃字幕成人| 大鸡操大B| 虐逼高潮出水大鸡巴| 黄色污污污内射一区二区三区内射丝袜| 亚洲影视一区| 男人的天堂AV站| 抽插 射 av| 在线观看AV啊~好粗| 视频一区二区三区诱惑 | 美女操匕啊啊啊| 韩国大鸡巴操逼| 扒开逼操视频| 国人精精品视频在线免费| 人爽人操视频| 肛交内射网站9| 熟女 五十路亚洲一区| 北条麻妃肛交一区二区| 国产熟女强奸操逼视频| 先锋影音av蜜臀麻豆| 线观看一区二区中文字幕| 91搞屄在线播放|