亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push plate cylinder Sold to Cameroon

Release time:2023-11-12 15:29:02 Hits: Current position: Home > News

This article mainly introduces:

Cameroon hydraulic cylinder,push plate cylinder manufacturer,push plate cylinder

Cameroon push plate cylinder

(Cameroon push plate cylinder,produced by Hengyu Hydraulic Cylinder Factory)

push plate cylinder are widely used in Cameroon,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed push plate cylinder for customers from Cameroon.

Introduction to push plate cylinder:

The cavitation of the push plate cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the push plate cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

In use, the push plate cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the push plate cylinder.

The commonly used buffer structure of the push plate cylinder is composed of a piston boss and a push plate cylinder head groove. When the piston moves close to the push plate cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

push plate cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the push plate cylinder head itself is the guide sleeve of the piston rod, the push plate cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the push plate cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Answers to some questions about push plate cylinder:

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

What is the safety factor of 25MPa cylinder wall thickness?
Safety factor n can take 3 cylinder material allowable stress [s]=sb/n δ/D=0.08 ~ 0.3 cylinder wall thickness δ=PMAX*D/ (2.3[s]-3PMAX) δ/D≤0.08 cylinder wall thickness δ=PMAX*D/2[s] P < 16MPa, Pmax=1.5Pn; P > 16MPa, Pmax=1.25Pn cold-drawn tube or honing tube is better!

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
保定市| 婷婷五月色网| 久久大奶| 一级一级黄片| 快快干我啊国产| 超碰网免费在线| 黑人猛男强奸日本美女| 亚洲有码激情小说| 性侵白丝美女| 国产精品自拍啪啪啪啪啪| 日韩精品久久久久福利悠悠色| 亚洲成人美女一二三| 美女秒拍福利视频| 国产熟女第一页| 国产精品一区二区肥胖| 日韩AV操B美女 | 成人h视频日本一区二区| 狂插女优少妇在线| 后入1区| 最新日本免费三区| 欧美美女丈鸡巴| 骚女人爱操逼| AV色五月婷婷| 欧洲精品久久| 蜜臀av一区二区三区蜜乳| 日本不卡中文一区二区| 精品亚洲破处| 可以免费看的一区二区亚| 普兰店市| 透露自拍去干网| 白虎嫩逼视频网站| 国产超碰青青| 国产亚洲男女操逼AV| 白丝内射一区二区在线观看| 大鸡巴啊 av 浪叫| 久久久久久久久九人体艺术| 后入大屁股AV| 粉嫩20p| 在线看片日本中文字幕| 操女逼逼| 嗯嗯嗯国产综合视频|