亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Chile

Release time:2023-11-12 15:29:01 Hits: Current position: Home > News

This article mainly introduces:

Chile hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Chile series synchronous cylinder

(Chile series synchronous cylinder,produced by Hebei Hengyu company)

series synchronous cylinder are widely used in Chile,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed series synchronous cylinder for customers from Chile.

Introduction to series synchronous cylinder:

How the cavitation of the series synchronous cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the series synchronous cylinder, resulting in corrosive damage to the parts.

The pressure of the sliding surface of the series synchronous cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the series synchronous cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

When the series synchronous cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the series synchronous cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

series synchronous cylinder is the most important part of construction machinery, the traditional processing method is: broaching series synchronous cylinder block - fine boring series synchronous cylinder block - grinding series synchronous cylinder block. The rolling method is: broaching series synchronous cylinder block - fine boring series synchronous cylinder block - rolling series synchronous cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the series synchronous cylinder block is about 1-2 days, rolling 1 meter of the series synchronous cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the series synchronous cylinder increases by 25%. If the series synchronous cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality series synchronous cylinders, you must take the rolling production process. After the series synchronous cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about series synchronous cylinder:

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.

What is st represented in the cylinder formula?
St is the original unit of kinematic viscosity, the abbreviation of Stokes, that is, Stokes, short for S. cm2/s has now been used. 1 s (St) = 10^-4m2/s.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
97超碰逼逼| 亚洲多毛逼逼| 中国少妇日韩| 日女人逼91| 亚洲成人第一| 男生的鸡鸡插入女生的b里面 | 人人操人人插人人射| 美女大胸操逼骚逼| 天美传媒麻豆免费播放| 成人午夜美女性爱在线| 五月 中文 一区在线| 7月色婷婷综合| 中文字幕精品女同性恋| 真实在线操逼播放| 嗯嗯嗯视频在线看| 肥婆精品一区| 四品无码在线| 91丝袜高清在线| 蜜乳av 懂色av| 欧美成人一区二区三区片免费| 偷拍自拍少妇人妻性爱| 嗯嗯啊嗯啊视频在线免费观看| 亚洲精品肥熟免费播放| 久久国产精品推油按摩 | 陆河县| 欧美老司机视频在线看| 日逼无码视频播放| 欧美五月丁香婷婷| 女同牲恋一区二区| 婷婷在线色| 中韩黄色| 天天舔舔舔看天天约| 人妻操少妇| 女人张开腿让男人桶免费动态图| 亚洲AV成人精品日韩在线播放| 中文字幕免费一区二区| av伊人狠狠操| 天门市| 熟女激情AV| 又大又粗又黄的国产黄片| 亚洲一区二区三区爽片|