亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

lifting platform cylinder Sold to Switzerland

Release time:2023-11-12 15:28:53 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,lifting platform cylinder manufacturer,lifting platform cylinder

Switzerland lifting platform cylinder

(Switzerland lifting platform cylinder,produced by Hengyu Hydraulic Co., Ltd)

lifting platform cylinder are widely used in Switzerland,because of no need for deceleration device,long service life,smooth movement.So our company has designed lifting platform cylinder for customers from Switzerland.

Introduction to lifting platform cylinder:

If the piston rod and lifting platform cylinder are stuck or the lifting platform cylinder is blocked, at this time, no matter how to operate, the lifting platform cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the lifting platform cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

In the process of using the lifting platform cylinder, sometimes such a problem will occur, the lifting platform cylinder can not act immediately after the instruction of the lifting platform cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil lifting platform cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

The machining accuracy of the lifting platform cylinder depends on the level of equipment, production technology and testing means. lifting platform cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

lifting platform cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the lifting platform cylinder is placed for a period of time, the lifting platform cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

Answers to some questions about lifting platform cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操BAV亚洲爽爆AV| 国产臊逼| 国产情侣欧美日韩| 大香蕉新版在线| 91中文字幕有码在线观看| 女同性恋黄网一区二区| 久久嗯嗯嗯嗯啊啊啊| 黄色色婷久久久| 五月婷婷婷爱看| 欧美粗大鸡巴操美女| 视频好日本色| 啊啊啊肏逼在线欢看| 日本秋霞人妻在线| 插鸡八在线观看| 91户外插屄视频| 无套内内射蜜桃臀| 极品逼日| 男人的天堂av播放器| 欧美一级日皮片| 天天操夜夜曰| 亚洲三区一区在线观看免费在线观看| 日本少妇中出| 18禁美女网站一区二区三区| 熟妇一区二区三区视频日本强| 激情五月狠狠网| 九九色五月婷婷在线观看中文字幕在 | 未亡人中出邻居在线| 欧美成人一区二区三区在线视频| 国产十一区| 欧美大鸡吧大鸡吧插逼| 久播毛片一区二区| 搭讪色诱播放| 亚洲熟女久精品| 啊啊,嗯,嗯,用力视频| 欧美巨屌肏屄| 韩国美女一区二区| 亚洲一区色图片| 大几巴操逼逼| 男生操女生的逼视频网站| 情爱视频日本一区| 黑人大鸡巴巨吊在线|