亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic booster cylinder Sold to Bulgaria

Release time:2023-11-12 15:28:43 Hits: Current position: Home > News

This article mainly introduces:

Bulgaria hydraulic cylinder,hydraulic booster cylinder manufacturer,hydraulic booster cylinder

Bulgaria hydraulic booster cylinder

(Bulgaria hydraulic booster cylinder,produced by Hengyu Hydraulic Co., Ltd)

hydraulic booster cylinder are widely used in Bulgaria,because of no need for deceleration device,long service life,smooth movement.So our company has designed hydraulic booster cylinder for customers from Bulgaria.

Introduction to hydraulic booster cylinder:

Because of the slightly complex structure of the buffer hydraulic booster cylinder, sometimes there will be problems, such as when the hydraulic booster cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

The commonly used buffer structure of the hydraulic booster cylinder is composed of a piston boss and a hydraulic booster cylinder head groove. When the piston moves close to the hydraulic booster cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

When the hydraulic booster cylinder needs to be stored for a period of time, please follow the recommended methods: The hydraulic booster cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the hydraulic booster cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil hydraulic booster cylinder should not be in direct contact with water vapor for a long time. The hydraulic booster cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the hydraulic booster cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the hydraulic booster cylinder Before working, the hydraulic booster cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the hydraulic booster cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

How the cavitation of the hydraulic booster cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the hydraulic booster cylinder, resulting in corrosive damage to the parts.

Answers to some questions about hydraulic booster cylinder:

How to control the speed of the cylinder?
High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.

What is the material of the cylinder support ring?
Generally, it is polytetrafluoroethylene doped with copper powder, or polyformaldehyde, and copper sleeves, there are also nylon, resin and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲∨∧| 老太太操逼视频| 北岛玲在线热| 厨房 骚妇 视频| 大几巴操逼逼| 玖玖玖玖人妻| 2025免费十无码十在线播放| 久久99爱国产免费婷婷| 欧美人妻 在线播放| 人妻意外中出在线中文字幕| 亚洲熟女人妻高清一区二区三区| 日韩美女操逼试看视频| 成人午夜激情开心| 大香蕉男人的天堂| 日本淫公乱妇电影| 熟女亚洲分类一区二区| 女人操逼中文字幕| 日本天堂免费啪啪啪| 初撮五十路人妻av| 白虎被操在线| 日本一区二区我不卡| 欧美最粗又大黑人鸡吧视频| 鸣巴插小穴| 日韩国胖女人的逼| 爆操小美女| 操骚逼操操操| 日韩激情文学在线| 嗯嗯嗯啊啊啊哦哦哦视频| 蜜桃AV麻豆| 国产vs欧美视频在线观看| 国产精品九九九久久九九| 国产精品夫妻性生活黄片视频| 黄片大鸡巴插进去| 大香蕉在线不卡W| 人人舔人人操人人骚| 成人黄色国产日韩欧美| 抽插白浆呻吟大鸡巴| 美女和男人日逼视频| 中文字幕羞羞答答一区二区三区四区| 国产丝袜综合中文| 欧美国产剧情免费日韩在线|