亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stroke adjustable cylinder Sold to Ethiopia

Release time:2023-11-12 15:28:43 Hits: Current position: Home > News

This article mainly introduces:

Ethiopia hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

Ethiopia stroke adjustable cylinder

(Ethiopia stroke adjustable cylinder,produced by Hebei Hengyu company)

stroke adjustable cylinder are widely used in Ethiopia,because of simple structure and reliable operation,powerful torque,clever hydraulic energy conversion.So our company has designed stroke adjustable cylinder for customers from Ethiopia.

Introduction to stroke adjustable cylinder:

When the oil pressure of the stroke adjustable cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Do not enter foreign bodies when installing the stroke adjustable cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

stroke adjustable cylinder body inspection: The inner surface of the stroke adjustable cylinder and the piston seal are the main factors causing the leakage in the stroke adjustable cylinder, if the stroke adjustable cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the stroke adjustable cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

The assembly work of the stroke adjustable cylinder has a great impact on the quality of the stroke adjustable cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about stroke adjustable cylinder:

What hydraulic oil does servo cylinder generally use?
The medium used by the cylinder generally depends on the working condition of the use, including pressure, installation environment, sealing material, etc. I think the first thing to consider is the impact of the sealing material. Mineral oil is a good choice if it is not too fire-resistant or used in a high temperature environment. 1, servo cylinder features: closed-loop servo control, control accuracy of 0.01mm; Precise control of thrust, increase pressure sensor, control accuracy up to 1%; It is easy to connect with PLC and other control systems to achieve high precision motion control. Low noise, energy saving, clean, high rigidity, impact resistance, long life, simple operation and maintenance. 2, the servo cylinder can be fault-free in harsh environments, and the protection level can reach IP66.

For a cylinder with a piston diameter of 100mm and a system pressure of 10MPa, what is the thrust?
Thrust is 7850 kg. Piston area A= πR^2=7850 square mm =78.5 square cm 10MPa = 100kg/cm^2 "^2" is square F = A x P =78.5 x 100=7850 kg.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
四房婷婷五月天基地| 美女热水操B| 国产美女A片| 久久日韩看片一| 老司机AV福利影院| 五月婷成人免费视频| www.91久热9九r久.com| 91插入少妇| 日本美女天堂| 五月婷婷手机免费看| 麻豆国产之光32部视频| 观看亚洲色| 老司机av| 十堰市| 亚洲中出大全| 激情小说亚洲精品| 中国av一区| 美国AV成人吹潮| 亚洲日韩欧美在线观看不卡| 国产少妇人妻一区二区| 激情自拍网| 日本大鸡吧插骚逼视频| 综合亚洲伊人大香蕉| 国产超碰av在线| 鸡巴插嫩逼网站大全部| 91超碰在线免费观看| 一区二区毛片看美国| 91国产日韩综合| 俄罗斯美女日庇视频| 国产在线无圣光| 大香蕉与少妇片| 大黑屌 在线| 轻点插进来啊av免费在线观看| 亚洲欧美午夜成人在厕所尿尿| 中日黄色网络| 18禁小视频| 操噢美逼| 大鸡巴操美女在线| 被侵犯的人妻超碰| 女人呗操视频91| 自拍一区青青草超碰|