亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

press machine hydraulic cylinder Sold to Indonesia

Release time:2023-11-12 15:28:33 Hits: Current position: Home > News

This article mainly introduces:

Indonesia hydraulic cylinder,press machine hydraulic cylinder manufacturer,press machine hydraulic cylinder

Indonesia press machine hydraulic cylinder

(Indonesia press machine hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

press machine hydraulic cylinder are widely used in Indonesia,because of long service life,smooth movement,high work efficiency.So our company has designed press machine hydraulic cylinder for customers from Indonesia.

Introduction to press machine hydraulic cylinder:

The press machine hydraulic cylinder should be vented: when the press machine hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the press machine hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the press machine hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the press machine hydraulic cylinder, the oil is best entered and discharged from the highest point of the press machine hydraulic cylinder. press machine hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

How the cavitation of the press machine hydraulic cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the press machine hydraulic cylinder, resulting in corrosive damage to the parts.

When installing the press machine hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the press machine hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the press machine hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the press machine hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the press machine hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

The meaning of the press machine hydraulic cylinder model marked by the press machine hydraulic cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the press machine hydraulic cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the press machine hydraulic cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

Answers to some questions about press machine hydraulic cylinder:

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

Why is the cylinder not in place when the concrete pump truck changes the piston?
When the concrete pump truck changes the piston, the cylinder is not in place mainly because the transfer oil connecting the two cylinders is not completely drained. Sany and Zhonglian have a piston return switch, which can be used to back the piston to the cleaning tank. The elephant is equipped with a stop valve at the bottom of the oil cylinder, usually in the closed state, when opened, the piston can be returned to the cleaning tank, remember to close the valve after the piston is updated.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
制服丝袜高清视频射操插| 日韩欧美国产未满18| 激情色一区二区| 亚洲悠悠在线| 91人人妻人人操人人爽| 国产AV不卡高清一区二区三区| 日骚货视频| 肏视频在线免费观看| 色婷婷狠狠五月综合天色拍| 亚洲色熟女另类图区| 精品九九婷婷之看片| 被操到喷水网站| 欧美偷拍自拍网| 嗯嗯嗯嗯哦哦哦国产| 靠女生的逼| 日韩不卡在线18禁| 亚洲一二精品精品轻熟女| 狠操日韩小骚逼| 一级成人在线视频播放| 操女生好舒服好爽的视频网站| 久久午夜激情啪啪啪| 猛操美女的骚逼的视频网站| 一区国产美女视频| 91激情婷| 欧美最猛黑人又大又粗XXXⅩ| 石原莉奈视频网站免费观看| 蜜乳成人久久| 操小穴高清视频免费看| 91深爱五月婷婷国产| 国产男女操逼大片| 欧洲少妇粗大19P| 天天天天天舔舔舔舔舔| 大香蕉在线观看,国产| WWW,亚AV| 国产伦精品一区二区三区视频新| 极品福利视频一区二区| 日本人妻中文字幕中出片| 日韩性生活视频网站观看| 亚裔精品一二三区| 大鸡巴操婊子逼视频| 鸡霸艹美女|