亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Thailand

Release time:2023-11-12 15:28:22 Hits: Current position: Home > News

This article mainly introduces:

Thailand hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Thailand supporting cylinder

(Thailand supporting cylinder,produced by Hengyu Hydraulic Co., Ltd)

supporting cylinder are widely used in Thailand,because of no need for deceleration device,long service life,smooth movement.So our company has designed supporting cylinder for customers from Thailand.

Introduction to supporting cylinder:

The supporting cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the supporting cylinder, bite. Elimination method: When installing the supporting cylinder, ensure that the axis position of the supporting cylinder is consistent with the direction of movement; Make the load borne by the supporting cylinder as far as possible through the supporting cylinder axis, to avoid the phenomenon of eccentricity.

supporting cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the supporting cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the supporting cylinder. c. The supporting cylinder seal is extruded, if the O-ring is obviously extruded at the supporting cylinder seal, replace the supporting cylinder seal.

When the supporting cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the supporting cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil supporting cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical supporting cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the supporting cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

How to determine the working pressure of the supporting cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, supporting cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about supporting cylinder:

A hydraulic system functions three cylinders to maintain pressure, what components need to be used?
Two way cartridge valve can be selected for control. Two way cartridge valve advantages: 1) flow capacity is large, especially suitable for large flow occasions. 2) The spool has sensitive action and strong anti-clogging ability. 3) Good sealing, small leakage, oil flow through the valve pressure loss is small. 4) Simple structure, easy to standardize.

What is the main maintenance of the cylinder?
After disassembling the cylinder: 1, clean the cylinder and piston; 2, replace all seals; 3, if there is a valve to repair, to ensure sealing and flexible; 4, deal with all deformation parts; 5. Installation experiment.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本一区二区尿尿在线| 亚洲 欧美 自拍 偷拍 乱| 深爱五月在线激情AV| 无码333区| 国产精品日韩肛交| 后入大屁股国产视频| 人人操时时操| 中文字幕国产一级黄色片| 自拍视频在线81人妻| 大黑鸡八草白逼视频| 超碰蜜臀揉揉| 亚洲色tv色| 夫妻av在线| 人人槽人人爽| 在线观看亚州一二三区| 1福利在线| 嗯嗯嗯的啊啊啊啊啊性在线17c就久久 | 大鸡巴操逼51视频| 中文字幕一区二区精品日韩欧美| 欧美在线视频 美女| 大鸡巴日少妇好爽| 丰满美女艹B视频| 国产精品熟女激情网站| 公交车被cao到腿软H漫画视频| 国产一区偷拍AV| 日韩电影伦理一区二区三区| 色优优久久久久久| 沙田区| 日韩少妇官网| 麻豆女神放荡视频在线播放| 骚逼抽查视频| 精品福利有码| 亂伦国产一区二区三区91| 国产社区亚洲日韩| 日韩逼逼大逼| 91人妻人人添人人澡| 就去干亚洲激情| 淫妻无码在线| 美女被大鸡巴操3D| 中文字幕一在线无码在线免费观看| 日韩一级特级久久久|