亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Sudan

Release time:2023-11-12 15:28:20 Hits: Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Sudan synchronous hydraulic cylinder

(Sudan synchronous hydraulic cylinder,produced by Hengyu Group)

synchronous hydraulic cylinder are widely used in Sudan,because of high work efficiency,long service life,smooth movement.So our company has designed synchronous hydraulic cylinder for customers from Sudan.

Introduction to synchronous hydraulic cylinder:

When the control pressure of the hydraulic system is too low, the synchronous hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

When using the synchronous hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the synchronous hydraulic cylinder block. If the synchronous hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the synchronous hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the synchronous hydraulic cylinder, so that the working efficiency of the synchronous hydraulic cylinder is reduced.

The machining accuracy of the synchronous hydraulic cylinder depends on the level of equipment, production technology and testing means. synchronous hydraulic cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

When installing the synchronous hydraulic cylinder, the axial ends of the synchronous hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the synchronous hydraulic cylinder, there is axial expansion. If the two ends of the synchronous hydraulic cylinder are fixed, all parts of the synchronous hydraulic cylinder will be deformed. When disassembling the synchronous hydraulic cylinder, it is strictly forbidden to hammer the synchronous hydraulic cylinder and the piston surface, such as the synchronous hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

Answers to some questions about synchronous hydraulic cylinder:

What is the principle of electric cylinder?
Principle: The electric cylinder converts the rotating motion of the motor into the linear motion of the push rod through the mechanical movement of the lead screw and the lead screw pair. With the closed-loop control characteristic of servo motor, the precise control of thrust, speed and position can be realized easily. Using modern motion control technology, numerical control technology and bus (network) technology, the program and bus (network) control is realized. Because of its easy control and use, it will realize the precision motion control that the cylinder and hydraulic cylinder drive can not achieve. Electric cylinder application field: 1, coordinate manipulator: logistics transmission, automated production line. 2. Wave making machine. 3, parallel mechanism: experimental platform, simulation platform, antenna. 4. Parallel machine tools. 5. Medical equipment: CT, Kamar

A hydraulic system functions three cylinders to maintain pressure, what components need to be used?
Two way cartridge valve can be selected for control. Two way cartridge valve advantages: 1) flow capacity is large, especially suitable for large flow occasions. 2) The spool has sensitive action and strong anti-clogging ability. 3) Good sealing, small leakage, oil flow through the valve pressure loss is small. 4) Simple structure, easy to standardize.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩在线二区三区一区| 97大香蕉共享| 国产美女插逼视频免费| 午夜精品久久久99热使用方法 | 午夜操日本人逼逼逼逼| 日韩无码五月天无码婷婷一区二区三区| 肥熟老熟妇6 9| 台湾中文娱乐网一区二| 日本熟女大香蕉三区四区视频| 日妣视频免费| 一区二区久骚| 女人呗操视频91| 美女日B图| 隆回县| 男生使劲躁女生视频| 大黑屌欧美日韩国产美乳翘臀| 嗯啊快肏我快啊视频| 欧美黑人大鸡巴性猛干| 日本黄色录像少妇。| 大鸡吧操我av| 在线麻烦国产黄篇| 欧美、日韩、国产视频| 伊人福利碰| 大香蕉精品99| 男女大鸡巴擦擦擦| 天天天天天天日夜夜夜夜夜夜操| 韩国成人深夜| 日韩成人网站欧美| 宝兴县| 极品大片中出欧美日韩| 麻豆,黄片| 人妻中出一二三区| 色逼人妻骚| 88久久中文字幕| 色婷婷五月综合视频在线| 后入美女视频在线| 加勒比群交免费视频| 伊人大香樵超碰| 小骚逼喜欢大鸡巴| 少妇骚逼导航| 啊~嗯~操我好舒服网站视频|