亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Uruguay

Release time:2023-11-12 15:28:17 Hits: Current position: Home > News

This article mainly introduces:

Uruguay hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Uruguay reciprocating cylinder

(Uruguay reciprocating cylinder,produced by Hengyu Hydraulic Co., Ltd)

reciprocating cylinder are widely used in Uruguay,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed reciprocating cylinder for customers from Uruguay.

Introduction to reciprocating cylinder:

In the case of serious wear on the inner surface of the reciprocating cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the reciprocating cylinder manufacturing process for replacement. The reciprocating cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

The wear of the hard chromium plating layer of the reciprocating cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

reciprocating cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the reciprocating cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the reciprocating cylinder. c. The reciprocating cylinder seal is extruded, if the O-ring is obviously extruded at the reciprocating cylinder seal, replace the reciprocating cylinder seal.

If the reciprocating cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

Answers to some questions about reciprocating cylinder:

What is the cause of sound and vibration when the hydraulic cylinder is under load?
The main reason 1) may be that the load machinery has stuck phenomenon, and the resistance is large. 2) The hydraulic oil is not enough, or the filter is blocked by dirty things, and the oil is flooded. 3) There is a problem with the pump.

How to control the speed of the cylinder?
High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大香蕉午夜云资源| 美国疯狂操B视频| 欧美.日韩精品·吻草| 黑人大鸡巴干淫的美女视频| 襙逼美女裸逼美女| 91大神在线一区观看| 中文字幕在线永久在线1页| 曰欧美一级| 抽插岛国视频| 曰逼福利视频| 男女一区二区同性| 欧美白虎后入一区| 亚洲aⅴ国产精品| jiuyaoai9999| 午夜亚洲美女| 亚洲大胸美女被大鸡巴捅| 肥胖黑阴道一区二区在线免费视频 | 美女自慰91在线| 啊啊啊嗯嗯av| 日韩精品一区二区三区99| 嫩逼福利视频| 一线人妻区| 成年男女午夜小视频| 国产日本黄色| 三级片色网| 伊人91日韩国产| 国产资源五月亚洲婷婷一起草| 嗯啊操嗯啊操嗯视频| 又大又硬又鸡巴操B| 鸡巴免费视频入口| 日韩高清无码三区| av高清一区不卡| 日欧美极品日欧美精品日欧美视频 | 日韩欧美嗯嗯好爽| 好叼操这里有精品| 96精品一区二区三区| 最新日韩久久| 看日韩操逼| 亚洲网黄官方入口| 大鸡巴操逼视| 亚洲欧美另类激情综合区粉芽|