亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

magnetic ring induction cylinder Sold to Sudan

Release time:2023-11-12 15:28:14 Hits: Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,magnetic ring induction cylinder manufacturer,magnetic ring induction cylinder

Sudan magnetic ring induction cylinder

(Sudan magnetic ring induction cylinder,produced by Hebei Hengyu company)

magnetic ring induction cylinder are widely used in Sudan,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed magnetic ring induction cylinder for customers from Sudan.

Introduction to magnetic ring induction cylinder:

The method of sleeve magnetic ring induction cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the magnetic ring induction cylinder can be significantly improved by rolling in the finishing of the inner holes of the magnetic ring induction cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

If the seal of the magnetic ring induction cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

If air enters the hydraulic system, the magnetic ring induction cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

When the piston speed of the magnetic ring induction cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the magnetic ring induction cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

Answers to some questions about magnetic ring induction cylinder:

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女欧美在线视频第一页| 性插一区| 大鸡吧日逼视频吗| 国产AV一区久久| 黑丝美女被艹在线看| 强干女人到高潮视频网址| 国产熟妇婬乱一区二区在线| 搞日逼视频| 三级在线中文| 大鸡巴操我一区| 工地操美女| 操女在线| 美国大鸡巴日B电影| 亚洲 午夜 福利 成人| 日本美女免费看操B视频| 五月超碰婷婷丁香青青| 日韩爱爱网页| 5G寂寞少妇渴望在线观看| 美女被插小穴高清| 亚洲欧美日韩香蕉| 黄片污污一级污| 91国际高清在线观看一区| 麻豆插屄AV| 欧美自拍大香蕉| 超碰在线最新97| 99亚洲熟女| 艹美女久久久91| 被老头狂操逼动态图| 艹B动图久久网| 午夜影音成人av| 国产日韩欧美综合大片在线播放| 大鸡巴插入骚逼网站| 日韩麻豆传媒性视频| 无码精品熟妇五十| 舔b在线看| 肥臀精品一区| 日本性熟妇一区| 巴东县| 中文字幕一区专区| 国产高清在线观看美女网站| 嗯嗯啊啊插中文字幕在线观看|