亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

lifter hydraulic cylinder Sold to Argentina

Release time:2023-11-12 15:28:11 Hits: Current position: Home > News

This article mainly introduces:

Argentina hydraulic cylinder,lifter hydraulic cylinder manufacturer,lifter hydraulic cylinder

Argentina lifter hydraulic cylinder

(Argentina lifter hydraulic cylinder,produced by Hebei Hengyu company)

lifter hydraulic cylinder are widely used in Argentina,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed lifter hydraulic cylinder for customers from Argentina.

Introduction to lifter hydraulic cylinder:

At the rated pressure, the thrust of the lifter hydraulic cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the lifter hydraulic cylinder is related to the diameter of the lifter hydraulic cylinder, but not to the stroke of the lifter hydraulic cylinder. Moreover, the larger the lifter hydraulic cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the lifter hydraulic cylinder.

When installing the lifter hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the lifter hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the lifter hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the lifter hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the lifter hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

When the lifter hydraulic cylinder is in use, ensure that the lifter hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

The internal leakage of the lifter hydraulic cylinder should be prevented when the lifter hydraulic cylinder is used. The internal leakage of lifter hydraulic cylinder includes the leakage caused by excessive wear of lifter hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about lifter hydraulic cylinder:

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

How to remove the lifting cylinder from the forklift truck?
The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
午夜在线视频18| 国产插美女视频| 国产寂寞黑丝少妇自慰| 连裤袜高跟鞋久久久久| 97AV影视在线观看一区二区三区| 美女白丝逼逼| 国产精品欧美日韩另类视频| 91网站视频网站美女在线观看一区二区| 男女视频777在线播放| 日本大鸡巴插骚逼| 兰考县| 国产区19页16p| 美女被大鸡巴操操| 美国和久免费顶级AV| 欧美亚洲bt色狼| 开心五月国产91激情| 丰满人妻一区=区三区在线视频53| 黑人大粗鸡巴暴操日本妞| 操 美女大鸡巴| 最新国产美女操逼| 久久人体福利视频| 欧美操逼黄| AV先锋影视| 欧美黑鸡巴XXXXX| 成人天天色人人操| 精品人妻一区二区三区潮喷在线 | 大鸡吧操入美女逼逼| 制服丝袜麻豆网站| 亚洲 欧美 第一区 第二区| 日韩一区在线播放| 福利视频网站女生宿舍| 超碰首页| 国产传媒在线观看入口| 大鸡吧变态操逼| 欧美白虎福利喷水一区| 狠狠干bAV| 亚洲激情有码网| 丁香婷婷六月综合激情| 亚卅AV无一区二区| 一男一女操逼视频| 俺爱激情五月婷婷91|