亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Peru

Release time:2023-11-12 15:27:46 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Peru tilting furnace hydraulic cylinder

(Peru tilting furnace hydraulic cylinder,produced by Hengyu Group)

tilting furnace hydraulic cylinder are widely used in Peru,because of excellent fatigue and impact resistance,smooth movement,high work efficiency.So our company has designed tilting furnace hydraulic cylinder for customers from Peru.

Introduction to tilting furnace hydraulic cylinder:

The difference between the integral tilting furnace hydraulic cylinder and the split tilting furnace hydraulic cylinder: The integral tilting furnace hydraulic cylinder and the split tilting furnace hydraulic cylinder in the tilting furnace hydraulic cylinder are two different tilting furnace hydraulic cylinders, and they are very different. The whole tilting furnace hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split tilting furnace hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and tilting furnace hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

The tilting furnace hydraulic cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the tilting furnace hydraulic cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the tilting furnace hydraulic cylinder wall due to the stiffness and the weight of the parts, causing scars.

The repair method of tilting furnace hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

The internal leakage of the tilting furnace hydraulic cylinder should be prevented when the tilting furnace hydraulic cylinder is used. The internal leakage of tilting furnace hydraulic cylinder includes the leakage caused by excessive wear of tilting furnace hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about tilting furnace hydraulic cylinder:

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
超碰国庆日韩在线观看| 狠狠的干免费所有| 免费看干鸡巴| 橾鸡巴视频网站| 91大神看| oumeiqingqing| 秀山| 操大逼网站美国黄色网| 欧美老妇一二区| 亚洲AV成人无码一二三不卡| 自拍偷拍 人妻激情| 国产肥熟女一区二区三区免费| 亚洲XSXX欧美XX虐| 精选日韩白丝一区| 尤物视频亚洲在线观看| 嗯嗯人妻在线| 大鸡巴对小穴视频| 啊~嗯~操我~~嗯啊~啊~~视频~| 天天色天天操天天爽| 五月天色婷婷激情综合深爱| 欧美18网站| 91中文字幕精品久久久久人妻| 欧美一级A片在线观看无码一区| 日本动漫操操操操| 日韩被捅小穴| 超美女逼逼| 大鸡巴一区二区操| 艹逼日韩精品| 九操中文在綫| 中文黄色字幕| 美女干大鸡吧| 久操嗯啊| 精品一区蜜臀视频在线观看| 插嫩逼逼视频| 亚洲丝袜美腿久久| 日本成人黄色中文字幕| 91视频后入小穴逼| 人人肉揉揉| 深爱激情动网在线看| 骚逼被鸡巴超出水来视屏| 小穴流水了|