亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to Paraguay

Release time:2023-11-12 15:27:24 Hits: Current position: Home > News

This article mainly introduces:

Paraguay hydraulic cylinder,vehicle hydraulic cylinder manufacturer,vehicle hydraulic cylinder

Paraguay vehicle hydraulic cylinder

(Paraguay vehicle hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

vehicle hydraulic cylinder are widely used in Paraguay,because of long service life,smooth movement,high work efficiency.So our company has designed vehicle hydraulic cylinder for customers from Paraguay.

Introduction to vehicle hydraulic cylinder:

When the vehicle hydraulic cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the vehicle hydraulic cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

After the vehicle hydraulic cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

In recent years, the processing process of the vehicle hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

The pressure of the sliding surface of the vehicle hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the vehicle hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Answers to some questions about vehicle hydraulic cylinder:

What are the cylinder manufacturing processes?
Hydraulic cylinder processing process: 1, cylinder: a, material preparation (seamless steel pipe) → inspection (material certificate, etc.) → tempering (outsourcing: Some parts) → car (car round, shelf mouth, boring, flange stop, etc.) → tempered hardness test → welding (welded pipe joint base, flange and other accessories) → boring or honing (rough boring, fine boring, rolling) → car (hole slot or internal and external thread) → fitter (drilling) → inspection → rust prevention storage b, material preparation (forgings) → inspection (material certificate, inspection, etc.) → welding (blank butt welding) → welding inspection → car (rough car) → quality control (outsourcing: some parts) → car (car round, shelf mouth, boring stop, flange stop, etc.)

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲有码区妻| 熟女一区二区三区在线视频| 91欧美激情一区二区| 黑丝美女干炮视频| 达日县| 国产在线盗摄av| 国产熟女户外野战高潮Aⅴ| 丁香婷婷五月香蕉91| 大鸡巴肏屄大美女| 96亚洲精品| 美国老逼AV| 一区自拍人妻| 美女一区视频桃花| 国产1990久久久久久久久久| 婷日韩一区在线| 亚洲 黑丝 美女 操| 东京热2018中文字幕最新| 美女老逼逼| 穴 插 视频| 色播情人婷婷五月天| 被大鸡巴爆操出水| 得得干亚洲视频| 抽插啊啊啊不要一区二区三区视频| 外国操老逼网| 人人舔人人操人人骚| 国产 日韩 欧美 xxx video| 国产裸模精品一区二区三粉嫩| 台湾佬22中文娱乐网| 亚洲日韩国产一区AV| 操美女.com| 日本一区视日本一区二区| 久久久之热| 深夜激情伍月婷婷| 在线中文av一区| 国产青青草原一区二区三区| 制服丝袜在线播放中出| 欧美日韩夜福利| 少妇鸡巴免费观看| 蜜色 麻豆视频| 美女一区二区二三区avav| 视频一区二三四五区视频|