亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

press hydraulic cylinder Sold to Japan

Release time:2023-11-12 15:27:13 Hits: Current position: Home > News

This article mainly introduces:

Japan hydraulic cylinder,press hydraulic cylinder manufacturer,press hydraulic cylinder

Japan press hydraulic cylinder

(Japan press hydraulic cylinder,produced by Hebei Hengyu company)

press hydraulic cylinder are widely used in Japan,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed press hydraulic cylinder for customers from Japan.

Introduction to press hydraulic cylinder:

When the press hydraulic cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the press hydraulic cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

press hydraulic cylinder body inspection: The inner surface of the press hydraulic cylinder and the piston seal are the main factors causing the leakage in the press hydraulic cylinder, if the press hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the press hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

What kind of process is used in the press hydraulic cylinder to make high-quality press hydraulic cylinder products: the body is the main component of the press hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The press hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the press hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the press hydraulic cylinder increases by 25%. If the service life of the press hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. press hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the press hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and press hydraulic cylinder are stuck or the press hydraulic cylinder is blocked. At this time, no matter how to manipulate, the press hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the press hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

press hydraulic cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

Answers to some questions about press hydraulic cylinder:

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
www.啊啊啊塞满了| 午夜福利成| 老司机精品在线免费观看| 无圣光一区首页| 又肉棒一进一出久久视频| 鸡巴快进视频| 在线亚洲一区二区三区AV| 欧美性爱五月天综合网| 插插大骚逼逼| 人人人人操人人人人人上人人人| 精品在线进入观看| 成年午夜精品| 欧美日韩操逼最新网站| 久热一区在线观看| 男人超碰碰| 任我草在线观看视频| 午夜福利黄18禁| 日韩色情视频网址| 成人在线视频你懂的| 亚州免費視頻一二三四五區| 欧美国产污污视频一区二区三区| 国产一级AV直播大全| 日韩美女一二三区高清视频| 九九视频免费妇女高潮| 操逼网视频| 国产又粗又爽又猛又粗又黄的| 成人白虎网| c骚逼av| 91抠笔一区| av色中色天天干天| 曰韩精品一区二区AV| 国产无码爽爽爽| 久久婷婷五月播| 国产AV 1区2区| 嫩模av天天做| 美女大基吧| 欧美最新视频在线观看| 亚洲国内激情一区二区三区AV| 久久综合88中文色鬼| 免费观看插鸡视频| 老太太操逼视频|