亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Republic of Lithuania

Release time:2023-11-12 15:26:56 Hits: Current position: Home > News

This article mainly introduces:

Republic of Lithuania hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Republic of Lithuania tailplate hydraulic cylinder

(Republic of Lithuania tailplate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailplate hydraulic cylinder are widely used in Republic of Lithuania,because of clever hydraulic energy conversion,clever hydraulic energy conversion,high work efficiency.So our company has designed tailplate hydraulic cylinder for customers from Republic of Lithuania.

Introduction to tailplate hydraulic cylinder:

Protection of the tailplate hydraulic cylinder surface: During the dismantling process, safety protection should be carried out on the tailplate hydraulic cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the tailplate hydraulic cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the tailplate hydraulic cylinder should be cleaned up in time.

When the control pressure of the hydraulic system is too low, the tailplate hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

The piston rod of the tailplate hydraulic cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

If the tailplate hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the tailplate hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow tailplate hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the tailplate hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the tailplate hydraulic cylinder includes the leakage caused by excessive wear of the tailplate hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and tailplate hydraulic cylinder, and the phenomenon of "pulling the tailplate hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about tailplate hydraulic cylinder:

How to distinguish high pressure cylinder and low pressure cylinder?
There is no special definition of the cylinder, the so-called pressure classification refers to the pump low pressure (code L) container 0.1MPa ≤p < 1.6MPa; Medium pressure (code M) container 1.6MPa ≤p < 10.0MPa; High pressure (code H) vessel 10 MPa≤p < 100 MPa; Ultra-high pressure (code U) container p≥100MPa. (1MPa=9.8Kg)

What steel pipe does hydraulic cylinder use? This problem is very general. Carbon steel pipe or ordinary seamless steel pipe are all ok, but then there are rolling, quilting, heat treatment and other steps, and the requirements are different, the wall thickness is different, the material is different. It depends on the circumstances.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
色偷偷的操| 十月丁香超碰| 免费看大逼| 插逼逼视频免费观看| 国产日韩欧美亚一级视频| 大鸡巴的小骚逼视频| 福利 片 无码| 日本高清视频大香蕉| 蜜臀久久9999精品久久宅男| 国严业久牛产中文区一区一区三区| 五月天情色av| 人人艹人人艹| 美女露大逼91| 美腿丝袜91在线一区| 激情国产在线一区二区| 大肉棒一进一出网站视频| 精品一区AV电影在线| 小姐姐白白日白白操| 操逼视频真实免费| 欧美另类BB大| 日韩 av 导航 中文| 国产精品亲逼逼黑丝袜美女| 日韩国女主播福利免费网址| 网站黄色一二美女及| 女主播被操在线播放| 99精品在线手机视频| 和静县| 亚洲爽爽爽爽爽爽爽爽| 把小穴操大视频| 91久久精品无码人妻一区二区三区| 又长又粗又大黄片| 人妻在线社区导航| 国产小视频网| 亚洲理论视频在线观看免费| 日本40路熟妇| 欧美色图亚洲色图十| 国产爆操在线白虎l| 国产对白麻豆激情对白| 小穴在线一区| 中文字幕丝袜人妻熟女| 大香蕉欧美日韩欧美|