亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

road paving machine hydraulic cylinder Sold to Oman

Release time:2023-11-12 15:26:54 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

Oman road paving machine hydraulic cylinder

(Oman road paving machine hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

road paving machine hydraulic cylinder are widely used in Oman,because of powerful torque,excellent temperature resistance,no transmission clearance.So our company has designed road paving machine hydraulic cylinder for customers from Oman.

Introduction to road paving machine hydraulic cylinder:

When the road paving machine hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The road paving machine hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the road paving machine hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil road paving machine hydraulic cylinder should not be in direct contact with water vapor for a long time. The road paving machine hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the road paving machine hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the road paving machine hydraulic cylinder Before working, the road paving machine hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the road paving machine hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

road paving machine hydraulic cylinder can not drive the load troubleshooting: oil pressure is too low. road paving machine hydraulic cylinder selection specifications are too small. Leakage in road paving machine hydraulic cylinder or associated hydraulic system element.

If the seal of the road paving machine hydraulic cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and road paving machine hydraulic cylinder, and the phenomenon of "pulling the road paving machine hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The body of the road paving machine hydraulic cylinder on the processing process requirements: the body of the road paving machine hydraulic cylinder is an important and essential part of the road paving machine hydraulic cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the road paving machine hydraulic cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

Answers to some questions about road paving machine hydraulic cylinder:

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女草b| 大鸡吧好硬视频| 首页人妻熟女久久久久| 国产美女被艹逼| 欧美大骚逼嗷嗷| 国产精品摘花| 2022天天射夜夜干| 乱色婷婷情爱性生活综合| 国产大鸡巴高清在线不卡| 激情五月艺术中心大黑逼| 臀蜜91精品国产免费观看| 操逼日韩不卡一二| 韩国三级片成人网| 熟女视频97| 国产激情黄片| 色戒在线一区二区在线播放| 国产免费裸体肛交网站| 伊人福利综合| 911啪啪视频| 日韩欧美男女操逼视频| 666AV视频@| 小穴流液无码| 操骚逼老熟妇视频| 性色av色香蕉一区二区三区| 高清在线中文字幕一区三区| 无遮挡网站美女极品| 成人综合香蕉| 日韩成人精品卡一卡二| 久久婷婷综合五月| 老妇激情区| 日韩不卡一区二区三区四区五区| 美女操比视频一二三区| 18禁美女插入网站| 大香蕉福利老司机精品| www.欧美在线.com| 日本黑人乱偷人妻| 性少妇视频中国老女人| 欧美日韩免费片| 嗯嗯嗯舒服视频哦| 啊,奶子好大逼逼流水了好痒视频| 加勒比在线网址一起草视频|