亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Paraguay

Release time:2023-11-12 15:26:45 Hits: Current position: Home > News

This article mainly introduces:

Paraguay hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Paraguay servo hydraulic cylinder

(Paraguay servo hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

servo hydraulic cylinder are widely used in Paraguay,because of smooth movement,high work efficiency,long service life.So our company has designed servo hydraulic cylinder for customers from Paraguay.

Introduction to servo hydraulic cylinder:

When the servo hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the servo hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the servo hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Do not enter foreign bodies when installing the servo hydraulic cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

When the oil pressure of the servo hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

In the case of serious wear on the inner surface of the servo hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the servo hydraulic cylinder manufacturing process for replacement. The servo hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Answers to some questions about servo hydraulic cylinder:

What's the use of three oil pipes on the cylinder?
The cylinder usually has an upper and lower oil chamber, one is connected to the upper oil chamber, one is connected to the lower oil chamber, sometimes a hydraulic lock will be added, that is, a hydraulic control check valve to prevent accidents when the oil pipe breaks, so the third pipe should be the control oil pipe of the hydraulic control check valve.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91在线五码| 亚洲国产熟女精品网站| 就操美女视频| 黄色激情国产| 亚洲免费肛交网站| 操老太太无码| 欧亚在线精品一区二区三区| 91 制作片在线观看| 黄色昌库久久播| 久久超级对对碰中文字幕| 亚洲久久悠悠色悠| 欧洲无码精品一区| 日一日,干一天AV| 狠狠狠干视频| 午夜专场小视频在线观看| 亚洲乱美女嫩逼| 插抽视频网站| 不卡9区| 插小穴视频免费看| 91啦中文熟女| 人妖大鸡巴操丰满 美女| 人人操,人人爽,人人人| 艹逼片16P| 91无码视频1区| 二区三区在线视频| 国产女人逼视频| 国产91视频一区二区| 国产探花色| 亚洲男女日B成人免费视频| 肥胖女人性大毛片一级视频| 五月午夜视频| 人妻AV色欲久久一区二区三区 | 天天弄天天日天天内射| 亚洲丰满人妻一区二区三区 | 国产 骚操逼视频| 熟女少妇七区| 日韩人妻中文字幕不卡二区| 亚洲男人激情视频在线| 午夜老司机福利欧美| 14p日韩亚洲精品| 操死你免费视频播放 |