亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

roller press hydraulic cylinder Sold to Egypt

Release time:2024-01-05 16:43:09 Hits: Current position: Home > News

This article mainly introduces:

Egypt hydraulic cylinder,roller press hydraulic cylinder manufacturer,roller press hydraulic cylinder

Egypt roller press hydraulic cylinder

(Egypt roller press hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

roller press hydraulic cylinder are widely used in Egypt,because of long service life,smooth movement,high work efficiency.So our company has designed roller press hydraulic cylinder for customers from Egypt.

Introduction to roller press hydraulic cylinder:

If it is found that the roller press hydraulic cylinder lubrication is poor or the roller press hydraulic cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the roller press hydraulic cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the roller press hydraulic cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the roller press hydraulic cylinder center line. In this way, when the piston works in the roller press hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the roller press hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

When the piston speed of the roller press hydraulic cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the roller press hydraulic cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

When the hydraulic oil is not pumped into the roller press hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the roller press hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

The roller press hydraulic cylinder is not the same as the roller press hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the roller press hydraulic cylinder can not be used as a high-power power component, but the roller press hydraulic cylinder can be used as a relatively large power component, or the roller press hydraulic cylinder system can be used.

Answers to some questions about roller press hydraulic cylinder:

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

Why are the hydraulic cylinders out of sync? The reasons for the unsynchronous operation are as follows: 1, the deviation of the external load of the two cylinders, such as the different resistance and friction of the two cylinders will lead to imbalance. The displacement of the cylinder with low resistance will be larger. 2, the difference in internal friction, such as the difference between the piston and the cylinder of each cylinder, the friction between the piston rod and the seal causes the cylinder to be out of sync. 3. The different resistance of hydraulic oil along the pipeline of the two cylinders causes the cylinder to be out of sync. 4, the deviation of the control original adjustment causes the deviation of the flow to be out of sync, such as the use of an independent throttle valve for each cylinder will appear the difference in the flow of oil in and out of the oil affecting the synchronization of the two cylinders. 5. The cylinder support point of the supported part is initially different.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美一级内射| 俄罗斯美女被操视频| 嗯啊嗯啊H啊嗯啊H视频在线观看| 最新四季AV在线| 嗯嗯啊啊啊啊好深视频| 抽插白浆呻吟大鸡巴| 欧美日韩e片| 草国产操老女人| h片日韩欧美在线观看| 叉逼免费视频| 91视频吃鸡巴| 一区二区三区四区福利| 就去干 日韩 欧美| 欧洲亚洲一区二区三区天码| 免费国产一区二区三区| 成人在线视频福利| 大香蕉高清在线一区二区三区| 国产原刨国产AV一区二区三区| 欧美少妇性生活在线| 下载大鸡巴干小逼逼| 搭讪人妻一区二区中出| 丝袜美女骚逼网站| 家庭乱插国产中文字幕| 礼子在线看| 少妇熟女国产专区| 在线观看男人的天堂av| 久久 伊人国产| 欧美日韩一区视频| 费看美女尿尿的地方2025国产亚洲| 男人和女人鸡吧对鸡吧国产| 国产啊啊啊好爽好多水| 小妇刺激偷拍视频在线| 高雄县| 看骚逼高潮特写| 欧美大长腿美女抽插网站| 天天插一插日一日| 啊啊啊好爽嗯嗯视频| 欧美日韩在线无毒视频| 亚洲一二三区在线视频| 胖少妇1区2区| 欧美黄色区欧美xx一区|