亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Czech Republic

Release time:2023-12-14 15:50:24 Hits: Current position: Home > News

This article mainly introduces:

Czech Republic hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Czech Republic shearing machine cylinder

(Czech Republic shearing machine cylinder,produced by Hengyu Hydraulic Cylinder Factory)

shearing machine cylinder are widely used in Czech Republic,because of excellent temperature resistance,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed shearing machine cylinder for customers from Czech Republic.

Introduction to shearing machine cylinder:

When the shearing machine cylinder is in use, ensure that the shearing machine cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

The assembly work of the shearing machine cylinder has a great impact on the quality of the shearing machine cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the long-stroke shearing machine cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in shearing machine cylinder head seal damage, oil leakage, and piston sleep in the shearing machine cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the shearing machine cylinder; The piston and the piston rod are connected with a spherical joint.

The shearing machine cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure shearing machine cylinder can use 20 steel pipe, and the high pressure shearing machine cylinder can use 45 steel pipe.

Answers to some questions about shearing machine cylinder:

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

Why does the cylinder pop out of itself when it stops?
This situation has two possibilities, 1. There is more air in the system, so exhaust the gas. 2. The back pressure of the oil return is relatively large, check the oil return filter, check whether the cylinder has a rod cavity buffer is too tight, and choose a 3-position 4-way M-type valve for the reversing valve. In addition, after the shutdown, manually change the reversing valve back and forth several times, it should not rise out.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大鸡巴插逼里操视频| 午夜福利区一区二区| 久久福利大香蕉| 日本一道一区二区三区视频| 久久蜜桃和b95大香蕉| 大鸡巴使劲操我视频| 激情图区国产| 精品肥臀一区二区三区| 人妻色资源| 操逼插屁眼视频免费看的公司| 亚洲精品美女免在线久18禁一区| 国产精品 大神| 久久人妻爆操| 嗯,不要,好痒视频| 日日操夜夜操人人操人人干| 大香蕉啪啪的视频| 非洲日韩在线中文| 国产女主播喷浆高潮免费网站| 亚洲熟女少妇一区二区图片| 日韩成人视频高清观看网站| 中国美女福利网站| 亚洲激情性交| 国产女人逼视频| 日本一区二区色呦呦| 肏屄大鸡巴视频| 操女主播的嫩逼| 国产老熟小视频| 操大波美女视频欧美| 韩国成人视屏在线播放| 日韩性爱XXXXX| 大鸡巴操B网站| 国产又大又粗又猛又爽的视频| 欧美日韩国产春潮操逼逼| 91国际高清在线观看一区| 亚洲福利视频一区二区导航| 红桃视频日韩无码三级| 男人的天堂 少妇| 蜜臀视频91,在线观看| 在线观看石原莉奈的视频| 91精品视频一区二区三区四区五区| 国产一区aaavv|