亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Libya

Release time:2023-12-11 09:05:24 Hits: Current position: Home > News

This article mainly introduces:

Libya hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Libya stacker cylinder

(Libya stacker cylinder,produced by Hebei Hengyu company)

stacker cylinder are widely used in Libya,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed stacker cylinder for customers from Libya.

Introduction to stacker cylinder:

In use, the stacker cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the stacker cylinder.

The assembly work of the stacker cylinder has a great impact on the quality of the stacker cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The repair method of the stacker cylinder: the repair of the stacker cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

stacker cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards stacker cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the stacker cylinder guide is determined by the length of the stroke. Check the strength of stacker cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

Answers to some questions about stacker cylinder:

What components can control cylinder rising and falling speed and the speed is adjustable?
A throttle or special solenoid valve is required. The reversing valve can choose the three-position reversing valve with P-type middle function. When rising, the reversing valve can be changed to the middle position to achieve differential connection and the fastest speed. Add a combination valve one-way throttle valve in the oil return circuit, connection mode: when the cylinder rises, the oil flows back to the tank through the check valve, the throttle valve is reversed off, when the cylinder falls, the reversing valve is changed to the left or right position (see the structure of the valve), the check valve is reversed off, the oil returns to the tank through the throttle valve, and the speed can be adjusted through the throttle valve.

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产在线日本色网站| 熟女人妻一二三区免费| 少妇被大鸡巴艹高潮视频| 日本在线不卡2区| 国产精品日本诩吹| 大鸡巴插嫩逼网站| 阳曲县| 裸体大胸美女精品一二三区网站| 五十路女同| 逼逼美女| 高清网又粗又大| 成人区人妻精品一区二区蜜柚| 国产av福利一区| 操吊一区二区三区| 鸡巴撑开小穴视频| 我想看日本搞逼| 国产女精品| 日韩欧美国产视频在线观看情趣| 久久123成人不卡| 亚洲熟女一二三四区| 北条麻妃成人电影一区二区三区| 高清视频二三区在线观看| 色无语婷婷五月| 美女午夜福利视频网站| 日本色诱网站| 殴洲老阿姨性视一区二区| 日本一区二区三区免费不卡在线| 婷婷六月性交往| 亚洲欧洲乱码视频| 日韩老熟女在线视频综合网| 色加勒比东京热| 99大尺度视频在线观看 | 大吊视频一区| 午夜美女诱惑视频| 成人做性视频在线看| 秋霞一区二区三区小说| 在线看AV成人第一区| 波多野结衣中出黑人| 欧美美被操| 日韩精品自拍欧美一区XXX| 国产最新高清视频|