亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

Lifting cylinder Sold to Guatemala

Release time:2023-12-05 14:27:12 Hits: Current position: Home > News

This article mainly introduces:

Guatemala hydraulic cylinder,Lifting cylinder manufacturer,Lifting cylinder

Guatemala Lifting cylinder

(Guatemala Lifting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

Lifting cylinder are widely used in Guatemala,because of no need for deceleration device,long service life,smooth movement.So our company has designed Lifting cylinder for customers from Guatemala.

Introduction to Lifting cylinder:

Disassembly Lifting cylinder: When disassembly Lifting cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the Lifting cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the Lifting cylinder.

Do not enter foreign bodies when installing the Lifting cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

After the Lifting cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

The Lifting cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure Lifting cylinder can use 20 steel pipe, and the high pressure Lifting cylinder can use 45 steel pipe.

Answers to some questions about Lifting cylinder:

Why should the piston rod of the hydraulic cylinder be so precise? If you hope the cylinder has a long service cycle, then all parts need to be high-precision, not only the piston rod, but also the cylinder, the sealing groove, the surface roughness, the cylinder looks very simple. Any hydraulic factory can produce the cylinder, but the good cylinder is difficult to produce.

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
鸡巴免费视频入口| 欧美妓女小骚逼| 操小骚逼视频免费| 91天美精东在线观看| 亚洲有码色| 在线观看欧美后入| 婷婷 一区二区三区| 精品丰满熟女少妇一区二| 手机中文字幕丝袜美腿在线第一区二区| 白白操在线观看视频| 日本加勒比久久综合88| 胖胖少妇后入| 日本韩国啪啪一区| 天天射射射射射射舔舔舔干干干 | 欧美三二一在线视频| 被大鸡吧疯狂操小骚逼| 日韩厕所精品| 欧美干美女下面| 免费十国产十自拍视频精品| 青青青视频欧美在线免费观看| 韩国三级片在线精品视频| 嗯嗯嗯嗯嗯嗯啊啊啊啊啊啊网站| 日本天堂熟女免费视频| 欧洲黑人美女性爱视频| av女优一区二区三区不卡| 免费亚洲一区二区三区| 欧美日韩一级高清| 岚皋县| 极品少妇骚逼视频| 中文有码二页| 极品自拍偷拍| 欧美人妻久久精品| 啊嗯嗯哦好大啊爽哦嗯嗯视频| 91av大神| 小热草网站| 亚码视频日本在线观看| 怡红院最新| 毛片视频一区二区三区四区五区| 亚洲肉网| 大鸡巴曰日b视频| 操波多野结衣的逼|